LK Automation Limited
FX1S-14MR-D MITSUBISHI FX1S-14MR-D PLC
Brand:
MITSUBISHI
Name: PLC
Model: FX1S-14MR-D
Max input / output points: 14 points.
Power supply voltage: DC24V.
Input points: 8 points.
Output points: 6 points.
Output type: relay.
Power consumption (W): 19.
Weight (kg):0.3.
Size (WxHxD) mm:60x90x75.
Positioning and pulse output functions: a PLC cell can output 2 point 100KHz pulses at the same time.
PLC is equipped with 7 special positioning instructions,
Including zero return, absolute or relative address expression and special pulse output control.
Host has 10 points (6I/4O), 14 points (8I/6O), 20 points (12I/8O), 30 points (16I/14O) of 4 types.
This type of PLC is mainly used in all of the digital input, digital output control point of the device.
Can be directly connected to the 220V city power, built-in 8K step EEPROM memory, no battery, easy to maintain.
The series transistor output (MT) of the PLC, can be output 2 100KHz pulse, direct drive servo or stepper motor.
The series PLC can not be brought with the expansion module, but can be installed by the BD board to extend a small amount of I/O.
The series 1N through the installation of BD series PLC board, can achieve RS232, RS485, RS422 communication.
...More relevant models >>>>
Name: PLC
Model: FX1S-14MR-D
Max input / output points: 14 points.
Power supply voltage: DC24V.
Input points: 8 points.
Output points: 6 points.
Output type: relay.
Power consumption (W): 19.
Weight (kg):0.3.
Size (WxHxD) mm:60x90x75.
Positioning and pulse output functions: a PLC cell can output 2 point 100KHz pulses at the same time.
PLC is equipped with 7 special positioning instructions,
Including zero return, absolute or relative address expression and special pulse output control.
Host has 10 points (6I/4O), 14 points (8I/6O), 20 points (12I/8O), 30 points (16I/14O) of 4 types.
This type of PLC is mainly used in all of the digital input, digital output control point of the device.
Can be directly connected to the 220V city power, built-in 8K step EEPROM memory, no battery, easy to maintain.
The series transistor output (MT) of the PLC, can be output 2 100KHz pulse, direct drive servo or stepper motor.
The series PLC can not be brought with the expansion module, but can be installed by the BD board to extend a small amount of I/O.
The series 1N through the installation of BD series PLC board, can achieve RS232, RS485, RS422 communication.
Power supply: 110mA DC5V (PLC internal power supply), 80mA DC24V (through the power connector by the external power supply).
Analog input points: 4 points.
Voltage input: DC-10~10V.
Current input: DC-20~20mA, 4~20mA.
Weight: 0.2kg.
Dimensions: 55 x 90 x 87.
Voltage input and current input of 4 channels can be carried out,
Each channel can be specified as a current input or voltage input MITSUBISHI FX1S-14MR-D FX1S-14MR-D
Built in digital filter function and peak hold function, etc.,
Achieved a high speed of 500 AD S/ch conversion.
FX3UC-4AD can be connected to the FX3GC or FX3UC series. Max input / output points: 64 points.
Power supply voltage: 24VDC.
Input points: 32 points.
Output points: 32 points.
Output type: relay.
Power consumption: 35W MITSUBISHI FX1S-14MR-D.
Weight (kg):1.0.
Size (WxHxD) mm:220x90x87.
Note recording function, Component annotation can be recorded in the program register.
Online program editor, online change the program will not lose the working hours or stop production operation.
RUN/STOP switch, running on panel / stop switch easy to operate.
Remote maintenance, remote programming software can monitor, upload or uninstall programs and data via modem communications
Password protection, using a eight digit password to protect your program MITSUBISHI FX1S-14MR-D.
Clock function and hour meter function, all of the PLC FX2N has a real-time clock standard MITSUBISHI PLC.
Continuous scanning function, to define the operation cycle for the application of the continuous scan time.
Input filter adjustment function, you can use the input filter to smooth the input signal (in the basic unit x000 to x017) MITSUBISHI PLC. Memory format: EPROM.
Number of steps:
Can use up to 16000 steps.
Battery support: do not.
Method of writing and deleting: write and use ROM to write, use ultraviolet ray to delete. Max input / output points: 14 points MITSUBISHI PLC.
Supply voltage: 100 - 240VAC.
Input points: 8 points.
Output points: 6 points.
Output type: Transistor (source).
Power consumption (W): 19.
Weight (kg):0.3.
Size (WxHxD) mm:60x90x75.
All equipment is digital input and output point.
The total I/O points are not more than 30 points, and the input points are less than 16, the output points are less than 14.
Its MT series of PLC can drive 2 way servo or stepper, commonly used in the control system for a ssimple manipulator FX1S-14MR-D.
MITSUBISHI FX1S series PLC is suitable for the smallest package,
It is the preferred target for low cost users to seek powerful control over a limited range of I/0.
FX1S provides up to 30 I/O points, and caan be transmitted through serial communication data,
MT models also have the ability to locate, widely used in a variety of small mechanical equipment MITSUBISHI FX1S-14MR-D.
Analog input points: 4 points.
Voltage input: DC-10~10V.
Current input: DC-20~20mA, 4~20mA.
Weight: 0.2kg.
Dimensions: 55 x 90 x 87.
Voltage input and current input of 4 channels can be carried out,
Each channel can be specified as a current input or voltage input MITSUBISHI FX1S-14MR-D FX1S-14MR-D
Built in digital filter function and peak hold function, etc.,
Achieved a high speed of 500 AD S/ch conversion.
FX3UC-4AD can be connected to the FX3GC or FX3UC series. Max input / output points: 64 points.
Power supply voltage: 24VDC.
Input points: 32 points.
Output points: 32 points.
Output type: relay.
Power consumption: 35W MITSUBISHI FX1S-14MR-D.
Weight (kg):1.0.
Size (WxHxD) mm:220x90x87.
Note recording function, Component annotation can be recorded in the program register.
Online program editor, online change the program will not lose the working hours or stop production operation.
RUN/STOP switch, running on panel / stop switch easy to operate.
Remote maintenance, remote programming software can monitor, upload or uninstall programs and data via modem communications
Password protection, using a eight digit password to protect your program MITSUBISHI FX1S-14MR-D.
Clock function and hour meter function, all of the PLC FX2N has a real-time clock standard MITSUBISHI PLC.
Continuous scanning function, to define the operation cycle for the application of the continuous scan time.
Input filter adjustment function, you can use the input filter to smooth the input signal (in the basic unit x000 to x017) MITSUBISHI PLC. Memory format: EPROM.
Number of steps:
Can use up to 16000 steps.
Battery support: do not.
Method of writing and deleting: write and use ROM to write, use ultraviolet ray to delete. Max input / output points: 14 points MITSUBISHI PLC.
Supply voltage: 100 - 240VAC.
Input points: 8 points.
Output points: 6 points.
Output type: Transistor (source).
Power consumption (W): 19.
Weight (kg):0.3.
Size (WxHxD) mm:60x90x75.
All equipment is digital input and output point.
The total I/O points are not more than 30 points, and the input points are less than 16, the output points are less than 14.
Its MT series of PLC can drive 2 way servo or stepper, commonly used in the control system for a ssimple manipulator FX1S-14MR-D.
MITSUBISHI FX1S series PLC is suitable for the smallest package,
It is the preferred target for low cost users to seek powerful control over a limited range of I/0.
FX1S provides up to 30 I/O points, and caan be transmitted through serial communication data,
MT models also have the ability to locate, widely used in a variety of small mechanical equipment MITSUBISHI FX1S-14MR-D.
...More relevant models >>>>