LK Automation Limited LK Automation Limited
Download Sort: OMRON | MITSUBISHI | Proface | Mennekes | Yaskawa
Manual Download >> FX2N-48MT-D
MITSUBISHI FX2N-48MT-D Manual FX2N-48MT-D PROGRAMMING MANUAL II
Product model: FX2N-48MT-D
Name: PLC
Brand: MITSUBISHI
Sort: PROGRAMMING MANUAL II
File language: English
Max input / output points: 10 points.
Power supply voltage: 24VDC.
Input points: 6 points.
Output points: 4 points.
Output type: Transistor (source).
Power consumption (W): 6.
Weight (kg):0.22.
Size (WxHxD) mm:60x90x49.
All equipment is digital input and output point.
The total I/O points are not more than 30 points, and the input points are less than 16, the output points are less than 14 FX2N-48MT-D PROGRAMMING MANUAL II FX2N-48MT-D
Its MT series of PLC can drive 2 way servo or stepper, commonly used in the control system for a simple manipulator.
MITSUBISHI FX1S series PLC is suitable for the smallest package,
It is the preferred target for low cost users to seek powerful control over a limited range of I/0.
FX1S provides up to 30 I/O points, and can be transmitted through serial communication data,
MT models also have the ability to locate, widely used in a variety of small mechanical equipment FX2N-48MT-D PROGRAMMING MANUAL II. Power: 18.5kw.
Purpose: to suppress the power harmonics.
Connected to the inverter input, can be used to improve the power factor, reduce the input side of the high harmonic current.
According to the motor power used to select AC reactor FX2N-48MT-D PROGRAMMING MANUAL II.
(when the inverter capacity is greater than the motor capacity, is still based on the motor capacity to choose.) Power: 7.5kw.
Purpose: high frequency braking resistor.
The use rate of the built-in regenerative brake of the transducer can be promoted.
When using the FR-ABR type brake resistor, the short circuit piece between the terminal PR-PX is removed. Does not remove the short circuit chip will lead to overheating of the brake resistor.
The utilization rate of the regenerative braking should be less than the allowable brake use rate in the above table.
With the operating frequency of the brake resistor to reach 300 degrees C or higher, it is necessary to take protective measures and cooling.
MYS type resistor can be used. But please pay attention to the allowable brake use rate.
Do not remove the terminal P/+ and P1 between the short circuit chip, in addition to connecting the DC reactor.
The installation of thermal relay, to avoid overheating and burn the braking resistor. MITSUBISHI inverter FR-A720 series.
Voltage level: 3 phase 200V.
Frequency converter capacity: 15KW.
Inverter general area of domestic enterprises to occupy more than 80% of the market share,
Production of frequency converter, motor soft starter and other industrial automation control of the manufacturers, the use of heavy-duty desiign products,
Overload capacity, with super large start and running capacity, improve the automatic detection, protection and control performance,
Can start and control any type of heavy duty motor,
Products have been widely used in metallurgy, mining, paper, chemicals, building materials, machinery, electricity, and construction systems and other industrial transmission areas FX2N-48MT-D Manual FX2N-48MT-D Manual.
Related products
MITSUBISHI
PLC
FX2N-80MT-ESS/UL
MITSUBISHI PLC FX2N-80MT-ESS/UL
Max input / output points: 80 points. Su
MITSUBISHI
PLC
FX2N-80MT-D
MITSUBISHI PLC FX2N-80MT-D
Max input / output points: 80 points. Po
MITSUBISHI
Master station module for CC-Link
FX2N-16CCL-M
MITSUBISHI Master station module for CC-Link FX2N-16CCL-M
Master station module for CC-Link. FX2N-
MITSUBISHI
Analog output module
FX2N-2DA
MITSUBISHI Analog output module FX2N-2DA
Voltage input: DC010V, DC05V. Current