LK Automation Limited LK Automation Limited
Download Sort: OMRON | MITSUBISHI | Proface | Mennekes | Yaskawa
Manual Download >> FX2N-16MR-DS
MITSUBISHI FX2N-16MR-DS Manual FX2N-16MR-DS PROGRAMMING MANUAL II
Product model: FX2N-16MR-DS
Name: PLC
Brand: MITSUBISHI
Sort: PROGRAMMING MANUAL II
File language: English
MITSUBISHI inverter series: FR-A820.
Voltage level: three phase 200V.
Power: 3.7kw.
SLD converter rated current: 25A.
Structure and function: Standard model.
Type: CA.
Substrate coating: have.
Parameters can be selected by 4 different rated current and different overload rating (SLD (ultra light load) rated, LD (light load) rating, ND (general load) rating, HD (weight) FX2N-16MR-DS PROGRAMMING MANUAL II FX2N-16MR-DS
Type load) for selection.
You can choose the most suitable frequency converter for use; and by selecting a transducer with a SLD or LD rated level,
Be able to reduce the size of the device (compared with the FR-A700 series, to reduce the volume of equipment).
For applications that require high torque at low speeds, the HD rating is the most suitable FX2N-16MR-DS PROGRAMMING MANUAL II.
The controller is used to control and monitor the frequency converter through the network.
Standard corresponding RS-485 communication (MITSUBISHI converter protocol, Modbus-RTU protocol) data transmission speed up to 115200bps. Can be isolated from the output of the programmable controller, the a/b/c contact relay, SSR, Tr output.Power: 18.5kw.
Purpose: to suppress the power harmonics FX2N-16MR-DS PROGRAMMING MANUAL II.
Improve the power factor, reduce the input side of the high harmonic current.
Make sure that this option is installed in the FR-A820-03800 (75K) and FR-A840-02160 (75K) and above capacity and above capacity.
At the same time the installation options in the use of 75kW and above motor. (the IP55 series has a built-in DC reactor.)
According to the motor power used to select the DC reactor.
(when the inverter capacity is greater than the motor capacity, is still based on the motor capacity to choose.) The output signal can open collector output inverter host standard.
Can be from the voltage output terminal (AM0), the current output terminal (AM1) output analog signal (output frequency, output current, etc.).
Can be connected to the 20mA DC or 10V DC meter. "Max input / output points: 48 points.
Supply voltage: 100 - 240VAC.
Input points: 24 points.
Output points: 24 points.
Output type: transistor.
Power consumption: 50VA.
Weight (kg):0.85.
Size (WxHxD) mm:182x90x87.
Note recording function, Component annotation can be recorded in the program register.
Online program editor, online change the program will not lose the working hours or stop production operation.
RUN/STOP switch, running on panel / stop switch easy to operate.
Remote maintenance, remote programming software can monitor, upload or uninstall programs and data via modem communications
Password protection, using a eight digit password to protect your program FX2N-16MR-DS Manual.
Clock function and hour meter function, all of the PLC FX2N has a real-time clock standard.
Continuous scanning function, to define the operation cycle for the application off the continuous scan time FX2N-16MR-DS Manual.
Input filter adjustment function, you can use the input filter to smooth the input signal (in the basic unit x000 to x017).
Related products
MITSUBISHI
High speed counting module
FX2N-1HC
MITSUBISHI High speed counting module FX2N-1HC
Signal level: the DC5V, 12V, and 24V dif
MITSUBISHI
PLC
FX2N-16MT-001
MITSUBISHI PLC FX2N-16MT-001
Max input / output points: 16 points. Su
MITSUBISHI
LINK MELSEC-I/O master module
FX2N-16LNK-M
MITSUBISHI LINK MELSEC-I/O master module FX2N-16LNK-M
LINK MELSEC-I/O master module. DC5V cons
MITSUBISHI
Master station module for CC-Link
FX2N-16CCL-M
MITSUBISHI Master station module for CC-Link FX2N-16CCL-M
Master station module for CC-Link. FX2N-