LK Automation Limited LK Automation Limited
Brand: OMRON | MITSUBISHI | Proface | Mennekes | Yaskawa
Go Back >> Product Catalogues
FX2N-16LNK-M MITSUBISHI FX2N-16LNK-M Using CC-Link to control a variety of FA machines 
Brand: MITSUBISHI
Name: LINK MELSEC-I/O master module
Model: FX2N-16LNK-M
LINK MELSEC-I/O master module.
DC5V consumption current: 200mA.
High speed counter equipped with 6 to 8 channels.
FX series of all models are standard with a high-speed counter.
Through a simple procedure to achieve high speed control.
Through the CC-Link and a variety of machine communications, the province of wiring.
Using CC-Link to control a variety of FA machines.
FX3G (*) /FX3U (C) series can be expanded by CC-Link control points.
Data communication with various machines using Ethernet.
FX3 series through Ethernet expansion device,
The monitoring and maintenance of equipment can be easily carried out in a place far from the scene.
Various machine communication with MODBUS protocol
Special adapter for MODBUS communications,
FX3 series can be used as a master or slave station with a variety of MODBUS protocol machine communication.

Input / output mode: transistor output (drain).
Output points: 8 points.
DC5V internal consumption current: 75mA.
DC24V internal consumption current: 75mA.
In order to extend the input output of the device.
Also has a built-in power supply products.
The maximum number of points for the input and output is 256 MITSUBISHI FX2N-16LNK-M.
Expansion module: up to 16 units (in addition to the power expansion module)
The total number of CC-Link, AnyWireASLINK, and Bitty series of remote I/O is 512 points FX2N-16LNK-M Input points: 24 points.
Output points: 16 points.
Power supply voltage: AC160-240V.
Output type: relay output.
Built in CPU, power supply, input and output. While maintaining the convenience of FX1N while improving performance MITSUBISHI FX2N-16LNK-M.
Special adaptor and function expansion board can be installed and used FX3 series.
High speed operation.
Basic instructions: 0.21 s/ instruction.
Application instruction: 0.5 s/ instruction.
Large capacity memory.
Built in program memory 32000 steps.
EEPROM memory cartridge with program transfer function. Length: 2m.
Specification: MR-C. Length: 3.0m.
Specification: TB-FX round cable. Total input and output points: 48 points MITSUBISHI FX2N-16LNK-M.
Input points: 24 points.
Output points: 24 points.
Output type: relay output.
Power supply voltage: AC100-240V.
Input signal voltage: DC24V.
8K capacity of the RAM memory, the maximum can be extended to 16K.
CPU arithmetic processing speed of 0 MITSUBISHI LINK MELSEC-I/O master module. 08 S/ basic instructions.
On the right side of the FX2N series can be connected to the input and output expansion modules and special function modules MITSUBISHI LINK MELSEC-I/O master module.
The basic unit is built in the 2 axis independent maximum 20kHz positioning function (transistor output type).
Quick disconnect the terminal block, which adopts excellent maintainability to quickly disconnect the terminal blocks, even if the cable is then replaced by the cable MITSUBISHI LINK MELSEC-I/O master module.
Clock function and hour meter function, all of the PLC FX2N has a real-time clock standard.
Continuous scanning function, to define the operation cycle for the application of the continuous scan time.
Input filter adjustment function, you can use the input filter to smooth the input signal (in the basic unit x000 to x017).
Note recording function, Component annotation can be recorded in the program register.

Online program editor, online change the program will not lose the working hours or stop production operation FX2N-16LNK-M.
RUN/STOP switch, running on panel / stop switch easy to operate.
Remote maintenance, remote programming software can monitor, upload or uninstall programs and data via modem communications
Password protection, using a eight digit password to protect your program MITSUBISHI FX2N-16LNK-M.


...More relevant models >>>>
Last one: FX2N-64CL-M
next one: FX2N-32ASI-M