LK Automation Limited LK Automation Limited
Brand: OMRON | MITSUBISHI | Proface | Mennekes | Yaskawa
Go Back >> Product Catalogues
YASKAWA SGMCS-08E3B11 Rated torque: M \/ 200N YASKAWA SGMCS-08E3B11
Brand: Yaskawa
Name: Direct drive servo motor
Model: SGMCS-08E3B11
SGMCS small capacity type of direct drive servo motor.
Rated torque: M \/ 8.0N.
Servo motor outside diameter size: 290mm.
Serial encoder: 20 bit absolute value type (absolute value of 1 circles) (standard).
Design sequence: the size of the outer diameter of the service motor is marked as E model.
Flange specification: face C, reverse load side.
Optional specifications: no matching.
Under the condition of no speed reducer, the load is directly driven.
Can be realized from low speed to high speed of the strong smooth running
(instantaneous maximum torque: 6 ~ 600N \/ m, maximum speed: 250 ~ 500r\/min).
By using 20 bit high resolution encoder, the high precision can be carried out.
The use of hollow structure, convenient wiring and piping.
Use example:
Semiconductor manufacturing equipment.
Liquid crystal circuit board manufacturing equipment.
Various inspection and test equipment.
Electronic part packaging machine.
IC information processor.
IC inspection equipment.
A variety of automated machinery.
Robot。
Small capacity ratings and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: A.
Insulation withstand voltage: AC1500V 1 minutes.
Protection mode: fully enclosed self cooling type IP42 (except for the rotating part of the output shaft).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation

Full closed loop module.
Maximum applicable motor capacity: 0.5kw.
Power supply voltage: three phase AC200V.
Interface: MECHATROLINK- II communication command type (rotary servo motor).
Design sequence: A.
Hardware specifications: paint.
Matching (software): no matching (standard).
Matching (parameters): no matching (standard) YASKAWA SGMCS-08E3B11.
Optional modules: full closed loop module SGMCS-08E3B11
Full closed loop control system is used to control the rotating servo motor.
Please install the servo unit.
Using the position feedback signal which is output by the external encoder (linear grating ruler) installed on the side of the machine to realize the high precision and high response.
External encoder capable of corresponding high resolution (linear grating) YASKAWA SGMCS-08E3B11. High performance, use the best type of servo unit (purpose type).
Maximum applicable motor capacity: 5.0kw.
Power supply voltage: three phase AC200V.
Interface: MECHATROLINK-III communication command type (rotary servo motor).
Design sequence: A.
Hardware specifications: paint.
Function: to support the use of rotary table.
Use the best type of sigma -V-FT series
According to different uses, there are 5 equipped with a convenient function of the servo unit models YASKAWA SGMCS-08E3B11.
FT001 (vibration suppression function to upgrade specifications): by strengthening the vibration suppression function, shorten the positioning time YASKAWA Direct drive servo motor.
FT003 (pressure feedback function): high precision pressure control, to promote the high performance of the device YASKAWA Direct drive servo motor.
FT005 (support for rotary table purposes): with the rotation of the coordinate function and fixed point through the output function, can be smooth and high-precision control of rotary table.
FT006 (fixed point through the output function): no need to pass through the upper device can be set through the output (Chu Fa) YASKAWA Direct drive servo motor.
FT008 (absolute value system support): the absolute value of the system can be constructed by any upper controller. High performance, use the best type of servo unit (high performance).
Maximum applicable motor capacity: 1.0kw.
Power supply voltage: three phase AC400V.
Design sequence: A.
Hardware specifications: paint.
Interface: MECHATROLINK-III communication command type (linear servo motor).
Function: support 125 s communication cycle.
High performance sigma shaped -V-EX series.
2 models of high performance servo unitt SGMCS-08E3B11.
EX001 (support M- III high speed communication): the communication cycle is the minimum value of 125 s, which makes the response of the instruction becomes faster, and the track accuracy and processing ability are improved. YASKAWA SGMCS-08E3B11.
EX002 (no deviation of the specification): greatly improve the command tracking performance, and further improve the accuracy of trajectory control.


...More relevant models >>>>
Last one: SGMCS-07E3B11
next one: SGMCS-10E3B11