LK Automation Limited LK Automation Limited
Brand: OMRON | MITSUBISHI | Proface | Mennekes | Yaskawa
Go Back >> Product Catalogues
SGMSV-25A3A2E YASKAWA SGMSV-25A3A2E servo motor
Brand: Yaskawa
Name: servo motor
Model: SGMSV-25A3A2E
Sigma -V series servo motor SGMSV.
Rated output: 2.5kw.
Power supply voltage: AC200V.
Serial encoder: 20 bit absolute value type (standard).
Design sequence: standard.
Shaft end: straight shaft, without keyway (standard).
Optional: with oil seal, with the brake (DC24V).
Super power rate.
Variety is complete (1.0kW ~ 7.0kW, with hold brake).
Equipped with a high resolution serial encoder (20 bit).
Standard using IP67 (7.0kw for IP22).
Use example:
Placement machine.
Punch printed circuit board.
Machine tool feeding device.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: F.
Insulation withstand voltage: AC1500V 1 minutes (200V), AC1800V 1 minutes (400V).
Protection mode: fully enclosed self cooling type IP67 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation

Equipped with INDEXER functional type servo unit (kit type).
Maximum applicable motor capacity: 1.0kw.
Power supply voltage: three phase AC400V.
Interface: instruction selection and installation (linear servo motor).
Matching (hardware): paint.
Matching (software): standard.
Matching (parameter): standard YASKAWA SGMSV-25A3A2E.
Optional module: INDEXER+ full closed loop module.
Simple.
By programming and serial programming, easy implementation of motion control SGMSV-25A3A2E
Can also be installed through the Windows environment support tool (SigmaWin+) easy to start.
The I/O module can be connected with the upper controller simply.
Smart.
To support the operation of the main purpose of the positioning operation based on the program table YASKAWA SGMSV-25A3A2E.
The maximum number of programmable positioning points to 256 points.
With external positioning, JOG speed table operation, the origin of reversion, rich features such as programmable signal output.
I/O points for the input: 19 points, output: 16 points.
Speedy.
High speed and high precision positioning by combining with high performance V series.
Motion control can be realized without using motion controller YASKAWA SGMSV-25A3A2E. Servo motor SGMGH type.
Rated speed: 1500r\/min.
Power: 0.45kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit relative value.
Design sequence: high precision machine tool YASKAWA servo motor.
Shaft end: straight shaft with screw key.
Optional parts: no brake oil seal.
High speed feed series: high speed running when no load.
Complete separation of the main circuit and the control circuit,
Alarm can only turn off the main circuit power supply, easy to maintain YASKAWA servo motor.
Parameter setting device.
The parameters can be directly entered by the servo drive body.
Saving wiring.
Using a serial encoder, encoder wiring number than the original product reduced by 1\/2 YASKAWA servo motor.
Multi in one control: the use of the parameters of the switch can not use the torque, position, speed controlServo motor SGMGH type.
Rated speed: 1500r\/min.
Power: 5.5kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit relative value.
Design sequence: high precision machine tool.
Shaft end: taper 1\/10, with parallel key.
Optional parts: with DC90V brake.
High speed feed series: high speed running when no load.
Complete separation of the main circuit and the control circuit,,
Alarm can only turn off the main circuit power supply, easy to maintain SGMSV-25A3A2E.
Parameter setting device.
The parameters can be directly entered by the servo drive body.
Saving wiring.
Using a serial encoder, encoder wiring number tthan the original product reduced by 1\/2 YASKAWA SGMSV-25A3A2E.
Multi in one control: the use of the parameters of the switch can not use the torque, position, speed control


...More relevant models >>>>
Last one: SGMSV-20A3A2E
next one: SGMSV-30A3A2E