LK Automation Limited LK Automation Limited
Brand: OMRON | MITSUBISHI | Proface | Mennekes | Yaskawa
Go Back >> Product Catalogues
SGMPS-08ACA2CE Medium inertia flat type motor YASKAWA SGMPS-08ACA2CE Medium inertia 
Brand: Yaskawa
Name: Medium inertia flat type motor
Model: SGMPS-08ACA2CE
Sigma -V series servo motor SGMPS.
Rated output: 750W (0.75kw).
Power supply voltage: AC200V.
Serial encoder: 17 bit Delta (standard).
Design sequence: IP55 (standard).
Shaft end: straight shaft, without keyway (standard).
Optional: with hold brake (DC24V).
Corresponding to the RoHS instruction: in accordance with the RoHS directive.
Medium inertia
Flat type deep short
Equipped with high resolution serial encoder (17 bit)
Max speed up to 6000r\/min
Variety is complete (100W ~ 1.5kW, with hold brake)
Standard using IP55. Also applies to IP67 (optional).
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: B.
Insulation withstand voltage: AC1500V 1 minutes.
Protection mode: fully enclosed self cooling type IP65 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation

Large capacity SGMVV type servo motor.
Rated output: 30KW.
Voltage: three phase AC200V.
Serial encoder: 20 bit absolute value type.
Rated speed: 800r\/min.
The main mechanical structure: support mounting type, straight shaft (with keyway and screw).
Optional parts: keep the brake (DC24V), with dust.
The use of small, low inertia servo motor, also can give full play to the strength of the mechanical properties YASKAWA SGMPS-08ACA2CE SGMPS-08ACA2CE
The new model SGMVV with a rated output of 22~55KW, the amount of passenger speed 800r\/min and 1500r\/min products.
After the motor is installed, the phase is started to run immediately.
Even if the servo is not adjusted, as long as the moment of inertia is within the allowable range,
Even if the load changes, it can be driven stably, and the vibration will not happenSigma -v series servo unit SGDV YASKAWA SGMPS-08ACA2CE.
Maximum applicable motor capacity: 1kw.
Power supply voltage: three phase AC200V.
Design sequence: B type.
Interface: MECHATROLINK- III communication command type (linear servo motor).
Matching (hardware): base mounting type (standard).
Realize real time communication
With the maximum transmission speed of 100Mbps and the set of communication cycle 125S ~ 4ms, to achieve a more than 62 stations of the high speed control YASKAWA SGMPS-08ACA2CE.
Through the high speed of communication, can send and receive all kinds of control information in real time.
Contribute to cost savings
A maximum of 62 stations can be connected to the communication line, can significantly reduce wiring costs and time YASKAWA Medium inertia flat type motor YASKAWA Medium inertia flat type motor.
The command connector of the upper controller only needs 1,
Pulse generator for D/A converter or position instruction without speed / torque command.
High precision motion control is realized.
In addition to torque, position and speed control, but also to achieve high precision synchronization phase control YASKAWA Medium inertia flat type motor.
Because the control mode can be switched on line, the complicated mechanical action can be realized more effectively and smoothly.SGMCS small capacity type of direct drive servo motor.
Rated torque: M \/ 25N.
Servo motor outside diameter size: 135mm.
Serial encoder: 20 bit Delta (optional).
Design sequence: the outer diameter of the servo motor is marked as B, C and D.
Flange specifications: face C, reverse load side (lead).
Optional specifications: no matching.
Under the condition of no speed reducer, the load is directly driven.
Can be realized from low speed to high speed of the strong smooth running
(instantaneous maximum torque: 6 ~ 600N \/ m, maximum speed: 250 ~ 500r\/min).
By using 20 bit high resolution encoder, the high precision can be carried out.
The use of hollow structure, convenient wiring and piping.
Use example:
Semiconductor manufacturing equipment.
Liquid crystal circuit board manufacturing equipment.
Various inspection and test equipment.
Electronic part packaging machine.
IC information processor.
IC inspection equipment.
A variety of automated machinery.
Robot。
Small capacity ratings and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.

Heat resistance grade: A SGMPS-08ACA2CE.
Insulation withstand voltage: AC1500V 1 minutes.
Protection mode: fully enclosed self cooling type IP42 (except for the rotating part of the output shaft).
The use of environmental humidity: 20 ~ 80%% (not dew) YASKAWA SGMPS-08ACA2CE.
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation


...More relevant models >>>>
Last one: SGMPS-04ACA2CE
next one: SGMPS-15ACA2CE