Servo motor SGMGH type.
Rated speed: 1000r\/min.
Power: 1.2kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit relative value.
Design sequence: B.
Shaft end: straight shaft with screw key.
Optional parts: with DC24V brake.
High speed feed series: high speed running when no load.
Alarm can only turn off the main circuit power supply, easy to maintain.
Parameter setting device.
The parameters can be directly entered by the servo drive body.
Saving wiring.
Using a serial encoder, encoder wiring number than the original product reduced by 1\/2.
Multi in one control: the use of the parameters of the switch can not use the torque, position, speed control
Servo motor type SGMAH (speed: 3000r/min).
Power: 0.1kw.
Power supply voltage: single phase AC100V.
Serial encoder: 13 bit relative value.
Design sequence: A.
Shaft end: straight shaft with screw key.
Optional parts: with DC90V brake.
Improve mechanical properties.
In order to achieve a higher production efficiency, SGDMAH type to the best control to explore the highest performance of the machine,
Compared with the original models, CPU computing time for its 1/2, through the expansion of the new control algorithm,
Positioning time is shortened to the original product of 1/3, to achieve a good response YASKAWA SGMGH-12ACB6C
SGMGH-12ACB6C
The parameter setting and maintenance time is shortened.
In order to establish a high degree system in a short time, the use of the simplicity of the YASKAWA SGMGH-12ACB6C.
Flexible use of online automatic adjustment function,
Automatic adjustment of servo system with mechanical characteristics.
Then use the main loop / control circuit power separation and alarm tracking memory function, can be simple to carry out maintenance.Index function type servo unit (box type).
Maximum applicable motor capacity: 0 YASKAWA SGMGH-12ACB6C. 4kw.
Power supply voltage: three phase ac200v.
Interface: instruction selection and installation (rotary servo motor).
Matching (hardware): basic installation type (standard).
Matching (software): standard.
Match (parameter): standard YASKAWA servo motor.
Optional module: index module.
Ordinary。
Through programming and serial programming, easy to achieve motion control.
Can also be installed in the Windows environment to support the tool (sigmawin +) start easily YASKAWA servo motor.
The I / O module can be simply connected to the controller.
Smart.
Support the operation of the main purpose of the positioning of the operating table based on the.
The maximum number of programmable positioning points to 256 points YASKAWA servo motor.
With external positioning, jogging speed table operation, the origin of the reversal, rich features, such as programmable signal output.
Input I / O points: 19 points, output: 16 points.
Fast.
High speed and high precision positioning of high performance V series combination.
Motion control can be achieved without the use of motion controller.Sigma -V series servo motor SGMGV.
Rated output: 11kw.
Power supply voltage: AC400V.
Serial encoder: 20 bit Delta (standard).
Design sequence: Standard (bolt for silver).
Shaft end: straight shaft, without keyway (standard).
Optional: with hold brake (DC24V).
A variety of mechanical feed shaft drive (high speed feed).
Variety is complete (300W ~ 15kW, with hold brake).
Equipped with a high resolution serial encoder (20 bit).
Standard using IP67.
Use example:
Machine tool。
Transport machinery.
Handling machinery。
Food processing machinery.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resiistance grade: F SGMGH-12ACB6C.
Insulation withstand voltage: AC1500V 1 minutes (200V), AC1800V 1 minutes (400V).
Protection mode: fully enclosed self cooling type IP67 (except shaft through part).
The use of environmental humidity: 20 ~ 80%% (not dew) YASKAWA SGMGH-12ACB6C.
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation