LK Automation Limited
SGMCS-14EDB41 Rated torque: M \/ 14N YASKAWA SGMCS-14EDB41
Brand:
Yaskawa
Name: Direct drive servo motor
Model: SGMCS-14EDB41
SGMCS small capacity type of direct drive servo motor.
Rated torque: M \/ 14N.
Servo motor outside diameter size: 290mm.
Serial encoder: 20 bit Delta (optional).
Design sequence: the size of the outer diameter of the service motor is marked as E model.
Flange specifications: face C, reverse load side (lead).
Optional specifications: no matching.
Under the condition of no speed reducer, the load is directly driven.
Can be realized from low speed to high speed of the strong smooth running
(instantaneous maximum torque: 6 ~ 600N \/ m, maximum speed: 250 ~ 500r\/min).
By using 20 bit high resolution encoder, the high precision can be carried out.
The use of hollow structure, convenient wiring and piping.
Use example:
Semiconductor manufacturing equipment.
Liquid crystal circuit board manufacturing equipment.
Various inspection and test equipment.
Electronic part packaging machine.
IC information processor.
IC inspection equipment.
A variety of automated machinery.
Robot。
Small capacity ratings and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: A.
Insulation withstand voltage: AC1500V 1 minutes.
Protection mode: fully enclosed self cooling type IP42 (except for the rotating part of the output shaft).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation
...More relevant models >>>>
Name: Direct drive servo motor
Model: SGMCS-14EDB41
SGMCS small capacity type of direct drive servo motor.
Rated torque: M \/ 14N.
Servo motor outside diameter size: 290mm.
Serial encoder: 20 bit Delta (optional).
Design sequence: the size of the outer diameter of the service motor is marked as E model.
Flange specifications: face C, reverse load side (lead).
Optional specifications: no matching.
Under the condition of no speed reducer, the load is directly driven.
Can be realized from low speed to high speed of the strong smooth running
(instantaneous maximum torque: 6 ~ 600N \/ m, maximum speed: 250 ~ 500r\/min).
By using 20 bit high resolution encoder, the high precision can be carried out.
The use of hollow structure, convenient wiring and piping.
Use example:
Semiconductor manufacturing equipment.
Liquid crystal circuit board manufacturing equipment.
Various inspection and test equipment.
Electronic part packaging machine.
IC information processor.
IC inspection equipment.
A variety of automated machinery.
Robot。
Small capacity ratings and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: A.
Insulation withstand voltage: AC1500V 1 minutes.
Protection mode: fully enclosed self cooling type IP42 (except for the rotating part of the output shaft).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation
Direct drive type servo motor SGMCV type.
Rated torque: M \/ 15N.
Servo motor diameter: diameter of 135mm.
Serial encoder: 22 bit (multi ring absolute encoder).
Design sequence: A.
Flange: reverse load side.
Optional parts: do not buy pieces.
Under the condition of no speed reducer, the load is directly driven YASKAWA SGMCS-14EDB41.
Can be realized from low speed to high speed of the strong smooth running
(instantaneous maximum torque: 12 ~ 75N \/ m, maximum speed: 500 ~ 600r\/min) SGMCS-14EDB41
By using 22 bit high resolution encoder, the high precision can be carried out.
The use of hollow structure, convenient wiring and piping.
Use example:
Semiconductor manufacturing apparatus.
Liquid crystal circuit board manufacturing device YASKAWA SGMCS-14EDB41.
Various inspection and test equipment.
Electronic component packaging machine.
C information processor.
C inspection equipment.
A variety of automated machinery.
ManipulatorServo motor SGMGH type.
Rated speed: 1500r\/min.
Power: 15Kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit relative value.
Design sequence: A.
Shaft end: taper 1\/10, with parallel key.
Optional parts: with DC90V brake YASKAWA SGMCS-14EDB41.
High speed feed series: high speed running when no load.
Complete separation of the main circuit and the control circuit,
Alarm can only turn off the main circuit power supply, easy to maintain.
Parameter setting device.
The parameters can be directly entered by the servo drive body YASKAWA Direct drive servo motor.
Saving wiring.
Using a serial encoder, encoder wiring number than the original product reduced by 1\/2 YASKAWA Direct drive servo motor.
Multi in one control: the use of the parameters of the switch can not use the torque, position, speed controlSigma -v series servo unit SGDV.
Maximum applicable motor capacity: 7.5kw.
Power supply voltage: three phase AC400V.
Design sequence: B type.
Interface: MECHATROLINK- III communication command type (rotary servo motor) YASKAWA Direct drive servo motor.
Matching (hardware): base mounting type (standard).
Realize real time communication
With the maximum transmission speed of 100Mbps and the set of communication cycle 125S ~ 4ms, to achieve a more than 62 stations of the high speed control.
Through the high speed of communication, can send and receive all kinds of control information in real time.
Contribute to cost savings
A maximum of 62 stations can be connected to the communication line, can significantly reduce wiring costs and time.
The command connector of the upper controller only needs 1,
Pullse generator for D/A converter or position instruction without speed / torque command SGMCS-14EDB41.
High precision motion control is realized.
In addition to torque, position and speed control, but also to achieve high precision synchronizzation phase control YASKAWA SGMCS-14EDB41.
Because the control mode can be switched on line, the complicated mechanical action can be realized more effectively and smoothly.
Rated torque: M \/ 15N.
Servo motor diameter: diameter of 135mm.
Serial encoder: 22 bit (multi ring absolute encoder).
Design sequence: A.
Flange: reverse load side.
Optional parts: do not buy pieces.
Under the condition of no speed reducer, the load is directly driven YASKAWA SGMCS-14EDB41.
Can be realized from low speed to high speed of the strong smooth running
(instantaneous maximum torque: 12 ~ 75N \/ m, maximum speed: 500 ~ 600r\/min) SGMCS-14EDB41
By using 22 bit high resolution encoder, the high precision can be carried out.
The use of hollow structure, convenient wiring and piping.
Use example:
Semiconductor manufacturing apparatus.
Liquid crystal circuit board manufacturing device YASKAWA SGMCS-14EDB41.
Various inspection and test equipment.
Electronic component packaging machine.
C information processor.
C inspection equipment.
A variety of automated machinery.
ManipulatorServo motor SGMGH type.
Rated speed: 1500r\/min.
Power: 15Kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit relative value.
Design sequence: A.
Shaft end: taper 1\/10, with parallel key.
Optional parts: with DC90V brake YASKAWA SGMCS-14EDB41.
High speed feed series: high speed running when no load.
Complete separation of the main circuit and the control circuit,
Alarm can only turn off the main circuit power supply, easy to maintain.
Parameter setting device.
The parameters can be directly entered by the servo drive body YASKAWA Direct drive servo motor.
Saving wiring.
Using a serial encoder, encoder wiring number than the original product reduced by 1\/2 YASKAWA Direct drive servo motor.
Multi in one control: the use of the parameters of the switch can not use the torque, position, speed controlSigma -v series servo unit SGDV.
Maximum applicable motor capacity: 7.5kw.
Power supply voltage: three phase AC400V.
Design sequence: B type.
Interface: MECHATROLINK- III communication command type (rotary servo motor) YASKAWA Direct drive servo motor.
Matching (hardware): base mounting type (standard).
Realize real time communication
With the maximum transmission speed of 100Mbps and the set of communication cycle 125S ~ 4ms, to achieve a more than 62 stations of the high speed control.
Through the high speed of communication, can send and receive all kinds of control information in real time.
Contribute to cost savings
A maximum of 62 stations can be connected to the communication line, can significantly reduce wiring costs and time.
The command connector of the upper controller only needs 1,
Pullse generator for D/A converter or position instruction without speed / torque command SGMCS-14EDB41.
High precision motion control is realized.
In addition to torque, position and speed control, but also to achieve high precision synchronizzation phase control YASKAWA SGMCS-14EDB41.
Because the control mode can be switched on line, the complicated mechanical action can be realized more effectively and smoothly.
...More relevant models >>>>
Related download