LK Automation Limited
SGMCS-05M3A11 YASKAWA Direct drive servo motor SGMCS-05M3A11
Brand:
Yaskawa
Name: Direct drive servo motor
Model: SGMCS-05M3A11
SGMCS small capacity type of direct drive servo motor.
Rated torque: M \/ 5.0N.
Servo motor outside diameter size: 280mm.
Serial encoder: 20 bit absolute value type (absolute value of 1 circles) (standard).
Design sequence: the outer diameter size of the servo motor is marked as N and M.
Flange specification: face C, load side.
Optional specifications: no matching.
Under the condition of no speed reducer, the load is directly driven.
Can be realized from low speed to high speed of the strong smooth running
(instantaneous maximum torque: 6 ~ 600N \/ m, maximum speed: 250 ~ 500r\/min).
By using 20 bit high resolution encoder, the high precision can be carried out.
The use of hollow structure, convenient wiring and piping.
Use example:
Semiconductor manufacturing equipment.
Liquid crystal circuit board manufacturing equipment.
Various inspection and test equipment.
Electronic part packaging machine.
IC information processor.
IC inspection equipment.
A variety of automated machinery.
Robot。
Small capacity ratings and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: A.
Insulation withstand voltage: AC1500V 1 minutes.
Protection mode: fully enclosed self cooling type IP42 (except for the rotating part of the output shaft).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation
...More relevant models >>>>
Name: Direct drive servo motor
Model: SGMCS-05M3A11
SGMCS small capacity type of direct drive servo motor.
Rated torque: M \/ 5.0N.
Servo motor outside diameter size: 280mm.
Serial encoder: 20 bit absolute value type (absolute value of 1 circles) (standard).
Design sequence: the outer diameter size of the servo motor is marked as N and M.
Flange specification: face C, load side.
Optional specifications: no matching.
Under the condition of no speed reducer, the load is directly driven.
Can be realized from low speed to high speed of the strong smooth running
(instantaneous maximum torque: 6 ~ 600N \/ m, maximum speed: 250 ~ 500r\/min).
By using 20 bit high resolution encoder, the high precision can be carried out.
The use of hollow structure, convenient wiring and piping.
Use example:
Semiconductor manufacturing equipment.
Liquid crystal circuit board manufacturing equipment.
Various inspection and test equipment.
Electronic part packaging machine.
IC information processor.
IC inspection equipment.
A variety of automated machinery.
Robot。
Small capacity ratings and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: A.
Insulation withstand voltage: AC1500V 1 minutes.
Protection mode: fully enclosed self cooling type IP42 (except for the rotating part of the output shaft).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation
Full closed loop module.
Maximum applicable motor capacity: 0.4kw.
Power supply voltage: three phase AC200V.
Interface: MECHATROLINK- II communication command type (rotary servo motor).
Design sequence: B.
Hardware specification: base mounting type (standard).
Matching (software): no matching (standard) YASKAWA SGMCS-05M3A11.
Matching (parameters): no matching (standard).
Optional modules: full closed loop module SGMCS-05M3A11
Full closed loop control system is used to control the rotating servo motor.
Please install the servo unit.
Using the position feedback signal which is output by the external encoder (linear grating ruler) installed on the side of the machine to realize the high precision and high response.
External encoder capable of corresponding high resolution (linear grating) YASKAWA SGMCS-05M3A11. Full closed loop module.
Maximum applicable motor capacity: 0.75kw.
Power supply voltage: single phase AC100V.
Interface: MECHATROLINK- II communication command type (rotary servo motor).
Design sequence: A.
Hardware specification: base mounting type (standard).
Matching (software): no matching (standard).
Matching (parameters): no matching (standard) YASKAWA SGMCS-05M3A11.
Optional modules: full closed loop module.
Full closed loop control system is used to control the rotating servo motor.
Please install the servo unit.
Using the position feedback signal which is output by the external encoder (linear grating ruler) installed on the side of the machine to realize the high precision and high response YASKAWA Direct drive servo motor.
External encoder capable of corresponding high resolution (linear grating) YASKAWA Direct drive servo motor. Sigma -v series servo unit SGDV.
Maximum applicable motor capacity: 0.5kw.
Power supply voltage: three phase AC200V.
Design sequence: B type.
Interface: MECHATROLINK- III communication command type (rotary servo motor).
Matching (hardware): base mounting type (standard) YASKAWA Direct drive servo motor.
Realize real time communication
With the maximum transmission speed of 100Mbps and the set of communication cycle 125S ~ 4ms, to achieve a more than 62 stations of the high speed control.
Through the high speed of communication, can send and receive all kinds of control information in real time.
Contribute to cost savings
A maximum of 62 stations can be connected to the communication line, can significantly reduce wiring costs and time.
The command connector of the upper controller only needs 1,
Pullse generator for D/A converter or position instruction without speed / torque command SGMCS-05M3A11.
High precision motion control is realized.
In addition to torque, position and speed control, but also to achieve high precision synchronizzation phase control YASKAWA SGMCS-05M3A11.
Because the control mode can be switched on line, the complicated mechanical action can be realized more effectively and smoothly.
Maximum applicable motor capacity: 0.4kw.
Power supply voltage: three phase AC200V.
Interface: MECHATROLINK- II communication command type (rotary servo motor).
Design sequence: B.
Hardware specification: base mounting type (standard).
Matching (software): no matching (standard) YASKAWA SGMCS-05M3A11.
Matching (parameters): no matching (standard).
Optional modules: full closed loop module SGMCS-05M3A11
Full closed loop control system is used to control the rotating servo motor.
Please install the servo unit.
Using the position feedback signal which is output by the external encoder (linear grating ruler) installed on the side of the machine to realize the high precision and high response.
External encoder capable of corresponding high resolution (linear grating) YASKAWA SGMCS-05M3A11. Full closed loop module.
Maximum applicable motor capacity: 0.75kw.
Power supply voltage: single phase AC100V.
Interface: MECHATROLINK- II communication command type (rotary servo motor).
Design sequence: A.
Hardware specification: base mounting type (standard).
Matching (software): no matching (standard).
Matching (parameters): no matching (standard) YASKAWA SGMCS-05M3A11.
Optional modules: full closed loop module.
Full closed loop control system is used to control the rotating servo motor.
Please install the servo unit.
Using the position feedback signal which is output by the external encoder (linear grating ruler) installed on the side of the machine to realize the high precision and high response YASKAWA Direct drive servo motor.
External encoder capable of corresponding high resolution (linear grating) YASKAWA Direct drive servo motor. Sigma -v series servo unit SGDV.
Maximum applicable motor capacity: 0.5kw.
Power supply voltage: three phase AC200V.
Design sequence: B type.
Interface: MECHATROLINK- III communication command type (rotary servo motor).
Matching (hardware): base mounting type (standard) YASKAWA Direct drive servo motor.
Realize real time communication
With the maximum transmission speed of 100Mbps and the set of communication cycle 125S ~ 4ms, to achieve a more than 62 stations of the high speed control.
Through the high speed of communication, can send and receive all kinds of control information in real time.
Contribute to cost savings
A maximum of 62 stations can be connected to the communication line, can significantly reduce wiring costs and time.
The command connector of the upper controller only needs 1,
Pullse generator for D/A converter or position instruction without speed / torque command SGMCS-05M3A11.
High precision motion control is realized.
In addition to torque, position and speed control, but also to achieve high precision synchronizzation phase control YASKAWA SGMCS-05M3A11.
Because the control mode can be switched on line, the complicated mechanical action can be realized more effectively and smoothly.
...More relevant models >>>>
Related download