LK Automation Limited
SGDV-1R7E11A YASKAWA MECHATROLINK- II communication command type servo unit YASKAWA SGDV-1R7E11A
Brand:
Yaskawa
Name: MECHATROLINK- II communication command type servo unit
Model: SGDV-1R7E11A
DC power input servo unit type SGDV.
Maximum applicable motor capacity: 11W.
Power supply voltage: DC48V.
Interface: MECHATROLINK- II communication command type (rotary servo motor).
Design sequence: A.
Realize real time communication.
The maximum transmission speed is 10Mbps, the communication cycle of 250 tested s ~ 4ms (depending on the device),
Can carry up to 30 stations of the high speed control. Through the high speed of communication, can send and receive all kinds of control information in real time.
Energy saving and high efficiency
A maximum of 30 stations can be connected to the communication lines, can significantly reduce the wiring costs and time.
The command connector of the upper controller only needs 1,
Pulse generator for D/A converter or position instruction without speed / torque command.
High precision motion control is realized.
In addition to torque, position and speed control, but also to achieve high precision synchronization phase control.
Because the control mode can be switched on line, the complicated mechanical efficiency can be realized more effectively and smoothly.
...More relevant models >>>>
Name: MECHATROLINK- II communication command type servo unit
Model: SGDV-1R7E11A
DC power input servo unit type SGDV.
Maximum applicable motor capacity: 11W.
Power supply voltage: DC48V.
Interface: MECHATROLINK- II communication command type (rotary servo motor).
Design sequence: A.
Realize real time communication.
The maximum transmission speed is 10Mbps, the communication cycle of 250 tested s ~ 4ms (depending on the device),
Can carry up to 30 stations of the high speed control. Through the high speed of communication, can send and receive all kinds of control information in real time.
Energy saving and high efficiency
A maximum of 30 stations can be connected to the communication lines, can significantly reduce the wiring costs and time.
The command connector of the upper controller only needs 1,
Pulse generator for D/A converter or position instruction without speed / torque command.
High precision motion control is realized.
In addition to torque, position and speed control, but also to achieve high precision synchronization phase control.
Because the control mode can be switched on line, the complicated mechanical efficiency can be realized more effectively and smoothly.
Servo motor SGMGH type.
Rated speed: 1500r\/min.
Power: 4.4kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit absolute value.
Design sequence: A.
Shaft end: straight shaft with screw key.
Optional parts: with oil seal, DC90V brake.
High speed feed series: high speed running when no load YASKAWA SGDV-1R7E11A.
Complete separation of the main circuit and the control circuit,
Alarm can only turn off the main circuit power supply, easy to maintain SGDV-1R7E11A
Parameter setting device.
The parameters can be directly entered by the servo drive body.
Saving wiring.
Using a serial encoder, encoder wiring number than the original product reduced by 1\/2.
Multi in one control: the use of the parameters of the switch can not use the torque, position, speed controlHigh performance, use the best type of servo unit (purpose type) YASKAWA SGDV-1R7E11A.
Maximum applicable motor capacity: 0.4kw.
Power supply voltage: single phase AC100V.
Interface: analog voltage, pulse sequence type (rotary servo motor).
Design sequence: B.
Hardware specifications: paint.
Function: vibration suppression function upgrade.
Use the best type of sigma -V-FT series
According to different uses, there are 5 equipped with a convenient function of the servo unit models YASKAWA SGDV-1R7E11A.
FT001 (vibration suppression function to upgrade specifications): by strengthening the vibration suppression function, shorten the positioning time.
FT003 (pressure feedback function): high precision pressure control, to promote the high performance of the device YASKAWA MECHATROLINK- II communication command type servo unit.
FT005 (support for rotary table purposes): with the rotation of the coordinate function and fixed point through the output function, can be smooth and high-precision control of rotary table YASKAWA MECHATROLINK- II communication command type servo unit.
FT006 (fixed point through the output function): no need to pass through the upper device can be set through the output (Chu Fa).
FT008 (absolute value system support): the absolute value of the system can be constructed by any upper controller YASKAWA MECHATROLINK- II communication command type servo unit. Large capacity SGMVV type servo motor.
Rated output: 45KW.
Voltage: three phase AC400V.
Serial encoder: 20 bit delta.
Rated speed: 1500r\/min.
The main mechanical structure: support mounting type, straight shaft (with keyway and screw).
Optional parts: do not buy pieces.
The use of small, low inertia servo motor, also can give full play to the strength oof the mechanical properties SGDV-1R7E11A.
The new model SGMVV with a rated output of 22~55KW, the amount of passenger speed 800r\/min and 1500r\/min products.
After the motor is installed, the phase is started to run immediately.
Even if the servo is not adjusteed, as long as the moment of inertia is within the allowable range,
Even if the load changes, it can be driven stably, and the vibration will not happen
Rated speed: 1500r\/min.
Power: 4.4kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit absolute value.
Design sequence: A.
Shaft end: straight shaft with screw key.
Optional parts: with oil seal, DC90V brake.
High speed feed series: high speed running when no load YASKAWA SGDV-1R7E11A.
Complete separation of the main circuit and the control circuit,
Alarm can only turn off the main circuit power supply, easy to maintain SGDV-1R7E11A
Parameter setting device.
The parameters can be directly entered by the servo drive body.
Saving wiring.
Using a serial encoder, encoder wiring number than the original product reduced by 1\/2.
Multi in one control: the use of the parameters of the switch can not use the torque, position, speed controlHigh performance, use the best type of servo unit (purpose type) YASKAWA SGDV-1R7E11A.
Maximum applicable motor capacity: 0.4kw.
Power supply voltage: single phase AC100V.
Interface: analog voltage, pulse sequence type (rotary servo motor).
Design sequence: B.
Hardware specifications: paint.
Function: vibration suppression function upgrade.
Use the best type of sigma -V-FT series
According to different uses, there are 5 equipped with a convenient function of the servo unit models YASKAWA SGDV-1R7E11A.
FT001 (vibration suppression function to upgrade specifications): by strengthening the vibration suppression function, shorten the positioning time.
FT003 (pressure feedback function): high precision pressure control, to promote the high performance of the device YASKAWA MECHATROLINK- II communication command type servo unit.
FT005 (support for rotary table purposes): with the rotation of the coordinate function and fixed point through the output function, can be smooth and high-precision control of rotary table YASKAWA MECHATROLINK- II communication command type servo unit.
FT006 (fixed point through the output function): no need to pass through the upper device can be set through the output (Chu Fa).
FT008 (absolute value system support): the absolute value of the system can be constructed by any upper controller YASKAWA MECHATROLINK- II communication command type servo unit. Large capacity SGMVV type servo motor.
Rated output: 45KW.
Voltage: three phase AC400V.
Serial encoder: 20 bit delta.
Rated speed: 1500r\/min.
The main mechanical structure: support mounting type, straight shaft (with keyway and screw).
Optional parts: do not buy pieces.
The use of small, low inertia servo motor, also can give full play to the strength oof the mechanical properties SGDV-1R7E11A.
The new model SGMVV with a rated output of 22~55KW, the amount of passenger speed 800r\/min and 1500r\/min products.
After the motor is installed, the phase is started to run immediately.
Even if the servo is not adjusteed, as long as the moment of inertia is within the allowable range,
Even if the load changes, it can be driven stably, and the vibration will not happen
...More relevant models >>>>