LK Automation Limited
SGDV-1R6A21B002000 YASKAWA Servo driver MECHATROLINK- III communication command type YASKAWA SGDV-1R6A21B002000
Brand:
Yaskawa
Name: Servo driver MECHATROLINK- III communication command type
Model: SGDV-1R6A21B002000
Sigma -v series servo unit SGDV.
Maximum applicable motor capacity: 0.2kw.
Power supply voltage: three phase AC200V.
Design sequence: B type.
Interface: MECHATROLINK- III communication command type (rotary servo motor).
Matching (hardware): paint.
Realize real time communication
With the maximum transmission speed of 100Mbps and the set of communication cycle 125S ~ 4ms, to achieve a more than 62 stations of the high speed control.
Through the high speed of communication, can send and receive all kinds of control information in real time.
Contribute to cost savings
A maximum of 62 stations can be connected to the communication line, can significantly reduce wiring costs and time.
The command connector of the upper controller only needs 1,
Pulse generator for D/A converter or position instruction without speed / torque command.
High precision motion control is realized.
In addition to torque, position and speed control, but also to achieve high precision synchronization phase control.
Because the control mode can be switched on line, the complicated mechanical action can be realized more effectively and smoothly.
...More relevant models >>>>
Name: Servo driver MECHATROLINK- III communication command type
Model: SGDV-1R6A21B002000
Sigma -v series servo unit SGDV.
Maximum applicable motor capacity: 0.2kw.
Power supply voltage: three phase AC200V.
Design sequence: B type.
Interface: MECHATROLINK- III communication command type (rotary servo motor).
Matching (hardware): paint.
Realize real time communication
With the maximum transmission speed of 100Mbps and the set of communication cycle 125S ~ 4ms, to achieve a more than 62 stations of the high speed control.
Through the high speed of communication, can send and receive all kinds of control information in real time.
Contribute to cost savings
A maximum of 62 stations can be connected to the communication line, can significantly reduce wiring costs and time.
The command connector of the upper controller only needs 1,
Pulse generator for D/A converter or position instruction without speed / torque command.
High precision motion control is realized.
In addition to torque, position and speed control, but also to achieve high precision synchronization phase control.
Because the control mode can be switched on line, the complicated mechanical action can be realized more effectively and smoothly.
Security module.
Maximum applicable motor capacity: 6.0kw.
Power supply voltage: three phase AC400V.
Interface: MECHATROLINK- II communication command type (rotary servo motor).
Design sequence: A.
Hardware specifications: shelf installation type + paint.
Matching (software): no matching (standard) YASKAWA SGDV-1R6A21B002000.
Matching (parameters): no matching (standard).
Optional module: security module SGDV-1R6A21B002000
European EC standards: Based on the integration of mechanical instructions standard ISO13849-1 EN,
Security module with individual standard 61800-5-2 IEC specified security function.
Through the combination of the SGDV servo unit, the best safety design of the mechanical system is realized.
Suitable for AC servo drive, with the following safety features specified in the international standard IEC61800-5-2 (Japan''s first) YASKAWA SGDV-1R6A21B002000.
Can easily achieve the best security design of mechanical systems.
Torque Off Safe (STO)
Stop Safe 1 (SS1)
Stop Safe 2 (SS2)
Limited Speed Safely (SLS)
Equipped with 2 security functions, can be set (distribution) security functions.
In addition, the monitoring time and other items can be changed through the parameter YASKAWA SGDV-1R6A21B002000.
With the use of the servo unit with a security module, so that the system can be simplified and miniaturized. Servo motor SGMGH type.
Rated speed: 1500r\/min.
Power: 5.5kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit absolute value.
Design sequence: high precision machine tool YASKAWA Servo driver MECHATROLINK- III communication command type.
Shaft end: taper 1\/10, with parallel key.
Optional parts: with DC24V brake YASKAWA Servo driver MECHATROLINK- III communication command type.
High speed feed series: high speed running when no load.
Complete separation of the main circuit and the control circuit,
Alarm can only turn off the main circuit power supply, easy to maintain.
Parameter setting device.
The parameters can be directly entered by the servo drive body YASKAWA Servo driver MECHATROLINK- III communication command type.
Saving wiring.
Using a serial encoder, encoder wiring number than the original product reduced by 1\/2.
Multi in one control: the use of the parameters of the switch can not use the torque, position, speed controlSigma -V series servo motor SGMAV.
Rated output: 0.2KW (200W).
Power supply voltage: AC200V.
Serial encoder: 20 bit Delta (standard).
Design sequence: standard.
Shaft end: with two side plane seat (optional).
Optional: with oil seal.
Super power rate.
Small capacity.
Ultra low inertia
Instantaneous maximum torque (rating 300%).
Equipped with a high resolution serial encoder (20 bit).
Max speed up to 6000r\/min.
Variety is complete (50W ~ 1.0kw, with hold brake).
Use example:
Semiconductor manufacturing equipment,
Placement machine,
Punch printed circuit board,
Robot，
Handling machinery，
Food processing machinery.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation mmethod: flange type SGDV-1R6A21B002000.
Heat resistance grade: B.
Insulation withstand voltage: AC1500V1 minutes.
Protection mode: fully enclosed self cooling type IP65 (except shaft through part).
The use of environmental humidity: 20 ~ 80%% (not dew) YASKAWA SGDV-1R6A21B002000.
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation
Maximum applicable motor capacity: 6.0kw.
Power supply voltage: three phase AC400V.
Interface: MECHATROLINK- II communication command type (rotary servo motor).
Design sequence: A.
Hardware specifications: shelf installation type + paint.
Matching (software): no matching (standard) YASKAWA SGDV-1R6A21B002000.
Matching (parameters): no matching (standard).
Optional module: security module SGDV-1R6A21B002000
European EC standards: Based on the integration of mechanical instructions standard ISO13849-1 EN,
Security module with individual standard 61800-5-2 IEC specified security function.
Through the combination of the SGDV servo unit, the best safety design of the mechanical system is realized.
Suitable for AC servo drive, with the following safety features specified in the international standard IEC61800-5-2 (Japan''s first) YASKAWA SGDV-1R6A21B002000.
Can easily achieve the best security design of mechanical systems.
Torque Off Safe (STO)
Stop Safe 1 (SS1)
Stop Safe 2 (SS2)
Limited Speed Safely (SLS)
Equipped with 2 security functions, can be set (distribution) security functions.
In addition, the monitoring time and other items can be changed through the parameter YASKAWA SGDV-1R6A21B002000.
With the use of the servo unit with a security module, so that the system can be simplified and miniaturized. Servo motor SGMGH type.
Rated speed: 1500r\/min.
Power: 5.5kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit absolute value.
Design sequence: high precision machine tool YASKAWA Servo driver MECHATROLINK- III communication command type.
Shaft end: taper 1\/10, with parallel key.
Optional parts: with DC24V brake YASKAWA Servo driver MECHATROLINK- III communication command type.
High speed feed series: high speed running when no load.
Complete separation of the main circuit and the control circuit,
Alarm can only turn off the main circuit power supply, easy to maintain.
Parameter setting device.
The parameters can be directly entered by the servo drive body YASKAWA Servo driver MECHATROLINK- III communication command type.
Saving wiring.
Using a serial encoder, encoder wiring number than the original product reduced by 1\/2.
Multi in one control: the use of the parameters of the switch can not use the torque, position, speed controlSigma -V series servo motor SGMAV.
Rated output: 0.2KW (200W).
Power supply voltage: AC200V.
Serial encoder: 20 bit Delta (standard).
Design sequence: standard.
Shaft end: with two side plane seat (optional).
Optional: with oil seal.
Super power rate.
Small capacity.
Ultra low inertia
Instantaneous maximum torque (rating 300%).
Equipped with a high resolution serial encoder (20 bit).
Max speed up to 6000r\/min.
Variety is complete (50W ~ 1.0kw, with hold brake).
Use example:
Semiconductor manufacturing equipment,
Placement machine,
Punch printed circuit board,
Robot，
Handling machinery，
Food processing machinery.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation mmethod: flange type SGDV-1R6A21B002000.
Heat resistance grade: B.
Insulation withstand voltage: AC1500V1 minutes.
Protection mode: fully enclosed self cooling type IP65 (except shaft through part).
The use of environmental humidity: 20 ~ 80%% (not dew) YASKAWA SGDV-1R6A21B002000.
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation
...More relevant models >>>>
Related download