LK Automation Limited
SAO-Q7N OMRON SAO-Q7N Current Sensor
Brand:
OMRON
Name: Current Sensor
Model: SAO-Q7N
Terminal/mounting: Plug-in/DIN rail via socket.
Control voltage: 100/110 VDC.
Overcurrent detection: Instantaneous type, W/start-up lock.
Solid-state, Plug-in Current Sensor.
Applicable to motor overcurrent protection and 3-phase AC current detection.
Inverse-type, start-up lock type, and instantaneous type over,
current sensors available.
Instantaneous type under current sensor available.
Plug-in design simplifies installation, removal, and wiring.
DIN sized (48 mm x 96 mm).
...More relevant models >>>>
Name: Current Sensor
Model: SAO-Q7N
Terminal/mounting: Plug-in/DIN rail via socket.
Control voltage: 100/110 VDC.
Overcurrent detection: Instantaneous type, W/start-up lock.
Solid-state, Plug-in Current Sensor.
Applicable to motor overcurrent protection and 3-phase AC current detection.
Inverse-type, start-up lock type, and instantaneous type over,
current sensors available.
Instantaneous type under current sensor available.
Plug-in design simplifies installation, removal, and wiring.
DIN sized (48 mm x 96 mm).
Rated input: 3-phase 3-wire mode, 3-phase 4-wire mode;
380, 400, 415, 480 VAC, 220, 230, 240, 277 VAC.
Ideal for Monitoring 3-phase Power.
Supplies for Industrial Facilities and Equipment.
Greater resistance to inverter noise.
Monitor overvoltages, undervoltages, phase sequence,
and phase loss for three-phase 3-wire or 4-wire power,
supplies with just one Unit OMRON SAO-Q7N.
Switch setting for 3-phase 3-wire or 3-phase 4-wire power supply SAO-Q7N
Two SPDT output relays, 5 A at 250 VAC (resistive load).
Output overvoltages and undervoltages using separate relays.
World-wide power specifications supported by one Unit (switchable).
Output status can be monitored using LED indicator. Type: Flat Cable.
Terminal Block: Terminal block with M3 OMRON SAO-Q7N. 5 screws.
Connector: Flat Cable Connectors*1.
No. of poles: 20.
Simplifies Connector and terminal,
block replacement, and requires less,
in-panel wiring.
Mount to DIN Track or via screws.
MIL Flat Cable Connectors and Multi-pole, Square,
Connectors are standard.
Terminal blocks available with either M3 or M3.5 screws.
Connecting Cables for Programmable Controllers,
available (sold separately) OMRON SAO-Q7N. Cable length L: A, 5.0 m; B, 4.75 m; C, 5.0 m.
Connect Connector-Terminal,
Block Conversion Units (XW2@) to,
I/O Units for Programmable,
Controllers with one touch. Square socket.
Equipped with a wide variety of square and round sockets,
Surface connection and back connection OMRON Current Sensor.
With a finger touch protection type.
With the fixed bracket, PYF cross tab OMRON Current Sensor.
Add no screw series. Cable: PUR.
Cable core number (core): 3.
Cable outside diameter: 4.3mm.
Cable outlet direction: L type.
Cable length L:10m.
The province, province hours maintenance, use waterproof connector environment and strong tolerance of FA.
Conform to IP67.
FA small special connector flame retardant 94V-0 OMRON Current Sensor.
The connector wiring system, convvenient equipment maintenance,
Reduce equipment downtime SAO-Q7N.
IEC61076-2-101 (IEC60947-5-2).
For LED products, can clearly confirm the status of the sensor action.
Type: Cable with Connectors on Both Ends (RJ45/RJ45).
Category: Cat.5 .
CCable sheath material: PUR OMRON SAO-Q7N.
Cable color: Green.
Cable length: 7.5 m.
Cables and Connectors for,
EtherCAT® and Other Industrial,
Ethernet Networks.
380, 400, 415, 480 VAC, 220, 230, 240, 277 VAC.
Ideal for Monitoring 3-phase Power.
Supplies for Industrial Facilities and Equipment.
Greater resistance to inverter noise.
Monitor overvoltages, undervoltages, phase sequence,
and phase loss for three-phase 3-wire or 4-wire power,
supplies with just one Unit OMRON SAO-Q7N.
Switch setting for 3-phase 3-wire or 3-phase 4-wire power supply SAO-Q7N
Two SPDT output relays, 5 A at 250 VAC (resistive load).
Output overvoltages and undervoltages using separate relays.
World-wide power specifications supported by one Unit (switchable).
Output status can be monitored using LED indicator. Type: Flat Cable.
Terminal Block: Terminal block with M3 OMRON SAO-Q7N. 5 screws.
Connector: Flat Cable Connectors*1.
No. of poles: 20.
Simplifies Connector and terminal,
block replacement, and requires less,
in-panel wiring.
Mount to DIN Track or via screws.
MIL Flat Cable Connectors and Multi-pole, Square,
Connectors are standard.
Terminal blocks available with either M3 or M3.5 screws.
Connecting Cables for Programmable Controllers,
available (sold separately) OMRON SAO-Q7N. Cable length L: A, 5.0 m; B, 4.75 m; C, 5.0 m.
Connect Connector-Terminal,
Block Conversion Units (XW2@) to,
I/O Units for Programmable,
Controllers with one touch. Square socket.
Equipped with a wide variety of square and round sockets,
Surface connection and back connection OMRON Current Sensor.
With a finger touch protection type.
With the fixed bracket, PYF cross tab OMRON Current Sensor.
Add no screw series. Cable: PUR.
Cable core number (core): 3.
Cable outside diameter: 4.3mm.
Cable outlet direction: L type.
Cable length L:10m.
The province, province hours maintenance, use waterproof connector environment and strong tolerance of FA.
Conform to IP67.
FA small special connector flame retardant 94V-0 OMRON Current Sensor.
The connector wiring system, convvenient equipment maintenance,
Reduce equipment downtime SAO-Q7N.
IEC61076-2-101 (IEC60947-5-2).
For LED products, can clearly confirm the status of the sensor action.
Type: Cable with Connectors on Both Ends (RJ45/RJ45).
Category: Cat.5 .
CCable sheath material: PUR OMRON SAO-Q7N.
Cable color: Green.
Cable length: 7.5 m.
Cables and Connectors for,
EtherCAT® and Other Industrial,
Ethernet Networks.
...More relevant models >>>>