LK Automation Limited
MR-H100TN MITSUBISHI Servo amplifier MR-H100TN
Brand:
MITSUBISHI
Name: Servo amplifier
Model: MR-H100TN
Drive: MR-H_ACN series CC-LINK features.
Rated output: 1.0KW.
The test system is composed of two parts, namely, the servo driver, the motor system and the host computer.
The host computer sends the speed command signal to the servo driver,
Servo drives start to run in accordance with the instructions.
In the course of operation, the running data of the servo system is collected by the host computer and the data acquisition circuit,
And carries on the preservation, the analysis and the display to the data. Because the motor is not loaded in this test system,
So compared with the previous two kinds of testing systems, the system has a relatively small volume,
And the measurement and control circuit of the system is relatively simple,
But it also makes the system can not simulate the actual operation of the servo drive.
Usually, such testing system is only used to test the rotational speed and angular displacement of the tested system under no-load condition,
And can not carry on the comprehensive and accurate test to the servo drive.
...More relevant models >>>>
Name: Servo amplifier
Model: MR-H100TN
Drive: MR-H_ACN series CC-LINK features.
Rated output: 1.0KW.
The test system is composed of two parts, namely, the servo driver, the motor system and the host computer.
The host computer sends the speed command signal to the servo driver,
Servo drives start to run in accordance with the instructions.
In the course of operation, the running data of the servo system is collected by the host computer and the data acquisition circuit,
And carries on the preservation, the analysis and the display to the data. Because the motor is not loaded in this test system,
So compared with the previous two kinds of testing systems, the system has a relatively small volume,
And the measurement and control circuit of the system is relatively simple,
But it also makes the system can not simulate the actual operation of the servo drive.
Usually, such testing system is only used to test the rotational speed and angular displacement of the tested system under no-load condition,
And can not carry on the comprehensive and accurate test to the servo drive.
MITSUBISHI motor universal AC servo amplifier MELSERVO-J3 series.
Rated output: 22.0kw.
Interface type: CC-Link communication type (built-in positioning function).
Power specification: three phase AC200V.
Positioning operation by setting position and rotational speed data in the positioning table and receiving the start signal from the main controller MITSUBISHI MR-H100TN.
The setting of the position and speed of the positioning table, as well as the start and stop operation can be completed through CC-Link communication MR-H100TN
By using the MR-J3-D01 extension IO unit, the DI/O instruction can be used to select and locate the table.
(CC-Link can not be used for MR-J3-D01 communications).
With built-in positioning function of the servo amplifier, can be set through the CC-Link communications and speed data MITSUBISHI MR-H100TN. (corresponding to the CC-Link version: Ver.1.10)
Can be achieved through the CC-Link communications to start, stop and monitoring and other operations.
Serial communication reduce wiring.
Distributed servo control system can be built by CC-Link communication.
The parameters of unit MR-PRU03 (optional) the parameter setting, operation and monitoring more convenient MITSUBISHI MR-H100TN.
The servo amplifier can be used for speed control operation.
When the two stations are occupied, the speed can be set directly by the remote register. Cable length: 30m.
For MR-J2S-700A (4) /CP/CL or less MITSUBISHI Servo amplifier.
Encoder for HC-SFS; HC-LFS; HC-RFS; 2000r/min HA-LFS; HC-UFS servo motor.
-H products have a long flex life.
Coding is not resistant to oil MITSUBISHI Servo amplifier.
MITSUBISHI general purpose AC servo amplifier MR-J2 series.
Rated output: 1.0kw.
Interface: general purpose interface.
Voltage: three phase AC200V.
MITSUBISHI servo system in the MITSUBISHI servo amplifier is widely used,
It can not only be used in the high precision position control and speed control of the working machinery and general industrial machinery,
Can also be used in the field of speed control and tension control MITSUBISHI Servo amplifier.
By installing a personal computer with a servo setting softwarre, the parameters setting, trial run, state display, and gain adjustment are performed MR-H100TN.
MITSUBISHI servo system MR-J2S column is developed on the basis of the servo MR-J2 series with a higher performance and more features of thhe MITSUBISHI servo system,
The control modes are position control, speed control and torque control, as well as the switching control mode among them MITSUBISHI MR-H100TN.
Rated output: 22.0kw.
Interface type: CC-Link communication type (built-in positioning function).
Power specification: three phase AC200V.
Positioning operation by setting position and rotational speed data in the positioning table and receiving the start signal from the main controller MITSUBISHI MR-H100TN.
The setting of the position and speed of the positioning table, as well as the start and stop operation can be completed through CC-Link communication MR-H100TN
By using the MR-J3-D01 extension IO unit, the DI/O instruction can be used to select and locate the table.
(CC-Link can not be used for MR-J3-D01 communications).
With built-in positioning function of the servo amplifier, can be set through the CC-Link communications and speed data MITSUBISHI MR-H100TN. (corresponding to the CC-Link version: Ver.1.10)
Can be achieved through the CC-Link communications to start, stop and monitoring and other operations.
Serial communication reduce wiring.
Distributed servo control system can be built by CC-Link communication.
The parameters of unit MR-PRU03 (optional) the parameter setting, operation and monitoring more convenient MITSUBISHI MR-H100TN.
The servo amplifier can be used for speed control operation.
When the two stations are occupied, the speed can be set directly by the remote register. Cable length: 30m.
For MR-J2S-700A (4) /CP/CL or less MITSUBISHI Servo amplifier.
Encoder for HC-SFS; HC-LFS; HC-RFS; 2000r/min HA-LFS; HC-UFS servo motor.
-H products have a long flex life.
Coding is not resistant to oil MITSUBISHI Servo amplifier.
MITSUBISHI general purpose AC servo amplifier MR-J2 series.
Rated output: 1.0kw.
Interface: general purpose interface.
Voltage: three phase AC200V.
MITSUBISHI servo system in the MITSUBISHI servo amplifier is widely used,
It can not only be used in the high precision position control and speed control of the working machinery and general industrial machinery,
Can also be used in the field of speed control and tension control MITSUBISHI Servo amplifier.
By installing a personal computer with a servo setting softwarre, the parameters setting, trial run, state display, and gain adjustment are performed MR-H100TN.
MITSUBISHI servo system MR-J2S column is developed on the basis of the servo MR-J2 series with a higher performance and more features of thhe MITSUBISHI servo system,
The control modes are position control, speed control and torque control, as well as the switching control mode among them MITSUBISHI MR-H100TN.
...More relevant models >>>>
Related download