LK Automation Limited
MITSUBISHI MR-H40TN So compared with the previous two kinds of testing systems, the system has a relatively small volume, Servo amplifier MR-H40TN
Brand:
MITSUBISHI
Name: Servo amplifier
Model: MR-H40TN
Drive: MR-H_ACN series CC-LINK features.
Rated output: 0.4KW.
The test system is composed of two parts, namely, the servo driver, the motor system and the host computer.
The host computer sends the speed command signal to the servo driver,
Servo drives start to run in accordance with the instructions.
In the course of operation, the running data of the servo system is collected by the host computer and the data acquisition circuit,
And carries on the preservation, the analysis and the display to the data. Because the motor is not loaded in this test system,
So compared with the previous two kinds of testing systems, the system has a relatively small volume,
And the measurement and control circuit of the system is relatively simple,
But it also makes the system can not simulate the actual operation of the servo drive.
Usually, such testing system is only used to test the rotational speed and angular displacement of the tested system under no-load condition,
And can not carry on the comprehensive and accurate test to the servo drive.
...More relevant models >>>>
Name: Servo amplifier
Model: MR-H40TN
Drive: MR-H_ACN series CC-LINK features.
Rated output: 0.4KW.
The test system is composed of two parts, namely, the servo driver, the motor system and the host computer.
The host computer sends the speed command signal to the servo driver,
Servo drives start to run in accordance with the instructions.
In the course of operation, the running data of the servo system is collected by the host computer and the data acquisition circuit,
And carries on the preservation, the analysis and the display to the data. Because the motor is not loaded in this test system,
So compared with the previous two kinds of testing systems, the system has a relatively small volume,
And the measurement and control circuit of the system is relatively simple,
But it also makes the system can not simulate the actual operation of the servo drive.
Usually, such testing system is only used to test the rotational speed and angular displacement of the tested system under no-load condition,
And can not carry on the comprehensive and accurate test to the servo drive.
Motor series: low inertia, medium capacity.
Rated output power: 37.0kw.
Rated speed: 1000rpm.
With the brake: without.
Shaft end: straight shaft.
The rotor of the servo motor is a permanent magnet, which is controlled by the U/V/W,
The rotor rotates under the action of the magnetic field, and the encoder feedback signal of the motor is given to the driver,
According to the feedback value and the target value, the driver adjusts the rotation angle of the rotor MITSUBISHI MR-H40TN MR-H40TN
Accuracy of the servo motor depends on the accuracy of the encoder (number of lines). Servo motor series: low inertia, medium and large capacity.
Rated output: 7.0kw.
Rated speed; 1500r/min.
Electromagnetic brake: No.
Power supply: 400V MITSUBISHI MR-H40TN.
Most suitable for medium and large capacity, low inertia type products in high frequency operation or acceleration and deceleration operation.
Improve the environmental performance of HG-SR, HG-JR series of products using IP67.
High speed & high torque. Shorten the positioning time, achieve high-speed equipment.
100 scene, there are 100 different drive control.
In order to meet the needs of the diverse and detailed field,
MR-J4 product line configuration, providing a wealth of servo amplifier and servo motor products MITSUBISHI MR-H40TN.
Can meet the different needs of different customers. Servo motor series: low inertia, medium and large capacity MITSUBISHI Servo amplifier.
Rated output: 0.5kw.
Rated speed; 3000r/min.
Electromagnetic brake: incidental.
Power supply: 400V.
Most suitable for medium and large capacity, low inertia type products in high frequency operation or acceleration and deceleration operation MITSUBISHI Servo amplifier.
Improve the environmental performance of HG-SR, HG-JR series of products using IP67.
High speed & high torque. Shorten the positioning time, achieve high-speed equipment.
100 scene, there are 100 different drive control MITSUBISHI Servo amplifier.
In order to meet the needs of the diverse and detailed field,
MR-J4 product line configuration, providing a wealth of servo amplifier and servo motor products.
Can meet the different needs of different customers. MITSUBISHI general purpose AC servo amplifier MELSERVO-J2-Super series.
Rated output: 11.0kw.
SSCNET interface.
Voltage: 3 phase AC200VAC or single phase AC230V.
Complete synchronization system with SSCNET high speed serial communication,
The communication cycle between the controller and the servo amplifier is the longest 0.888ms.
Such systems will be able to provide high reliability and high performance.
When connecting the servo system with SSCNET,
In the motion system, the parameters of the servo amplifier and the acquisition of the data will be displayed on the motion controller.
Connect a dedicated cable with an amplifier and a controller to form a SSCNET system.
This simple connection method reduces the routing time and helps to prevent noise MR-H40TN.
Even in the MELSERVO-J2-SUPER series products using high resolution coding standards, the command frequency is no limit.
It is only necessary to add a battery on the seervo amplifier, which can form the absolute value system MITSUBISHI MR-H40TN.
Currently there are more than 1000000 high reliability SSCNET servo amplifier networks in use.
Rated output power: 37.0kw.
Rated speed: 1000rpm.
With the brake: without.
Shaft end: straight shaft.
The rotor of the servo motor is a permanent magnet, which is controlled by the U/V/W,
The rotor rotates under the action of the magnetic field, and the encoder feedback signal of the motor is given to the driver,
According to the feedback value and the target value, the driver adjusts the rotation angle of the rotor MITSUBISHI MR-H40TN MR-H40TN
Accuracy of the servo motor depends on the accuracy of the encoder (number of lines). Servo motor series: low inertia, medium and large capacity.
Rated output: 7.0kw.
Rated speed; 1500r/min.
Electromagnetic brake: No.
Power supply: 400V MITSUBISHI MR-H40TN.
Most suitable for medium and large capacity, low inertia type products in high frequency operation or acceleration and deceleration operation.
Improve the environmental performance of HG-SR, HG-JR series of products using IP67.
High speed & high torque. Shorten the positioning time, achieve high-speed equipment.
100 scene, there are 100 different drive control.
In order to meet the needs of the diverse and detailed field,
MR-J4 product line configuration, providing a wealth of servo amplifier and servo motor products MITSUBISHI MR-H40TN.
Can meet the different needs of different customers. Servo motor series: low inertia, medium and large capacity MITSUBISHI Servo amplifier.
Rated output: 0.5kw.
Rated speed; 3000r/min.
Electromagnetic brake: incidental.
Power supply: 400V.
Most suitable for medium and large capacity, low inertia type products in high frequency operation or acceleration and deceleration operation MITSUBISHI Servo amplifier.
Improve the environmental performance of HG-SR, HG-JR series of products using IP67.
High speed & high torque. Shorten the positioning time, achieve high-speed equipment.
100 scene, there are 100 different drive control MITSUBISHI Servo amplifier.
In order to meet the needs of the diverse and detailed field,
MR-J4 product line configuration, providing a wealth of servo amplifier and servo motor products.
Can meet the different needs of different customers. MITSUBISHI general purpose AC servo amplifier MELSERVO-J2-Super series.
Rated output: 11.0kw.
SSCNET interface.
Voltage: 3 phase AC200VAC or single phase AC230V.
Complete synchronization system with SSCNET high speed serial communication,
The communication cycle between the controller and the servo amplifier is the longest 0.888ms.
Such systems will be able to provide high reliability and high performance.
When connecting the servo system with SSCNET,
In the motion system, the parameters of the servo amplifier and the acquisition of the data will be displayed on the motion controller.
Connect a dedicated cable with an amplifier and a controller to form a SSCNET system.
This simple connection method reduces the routing time and helps to prevent noise MR-H40TN.
Even in the MELSERVO-J2-SUPER series products using high resolution coding standards, the command frequency is no limit.
It is only necessary to add a battery on the seervo amplifier, which can form the absolute value system MITSUBISHI MR-H40TN.
Currently there are more than 1000000 high reliability SSCNET servo amplifier networks in use.
...More relevant models >>>>
Related download