LK Automation Limited
MITSUBISHI FX3U-48MR/DS Power consumption: 30W PLC FX3U-48MR/DS
Brand:
MITSUBISHI
Name: PLC
Model: FX3U-48MR/DS
Max input / output points: 48 points.
Power supply voltage: 24VDC.
Input points: 24 points.
Output points: 24 points.
Output type: relay.
Power consumption: 35W.
Weight (kg):0.85.
Size (WxHxD) mm:182x90x86.
Built in CPU, power supply, input and output. By using a rich variety of functional extension boards and special adapters,
Can achieve high precision control.
Based on the function of FX2N has been greatly strengthened and enhanced.
High speed operation.
Basic instructions: 0.065 s/ instruction.
Application instruction: 0.642 s/ instruction.
Large capacity memory.
Built in program memory 64000 steps.
Flash memory cartridge with program transfer function.
Authentication。
Corresponding EN and UL/cUL authentication.
Faster and more efficient. Support high speed control and network communication, and have the function of data recording.
High speed, large capacity, multi-function high-end machine.
FX3U supports high speed processing, CC-Link communication, network communication, analog control and advanced positioning system.
Connected to the CC-Link, including the remote I/O, the maximum input and output control points up to 384 points,
Can correspond to a variety of field needs, the use of its scalability and flexibility to expand the scope of application of the control system.
Third generation high function micro programmable controller.
High speed, high efficiency, high performance, large capacity, and new features.
Built in high speed processing and positioning.
Control points: maximum 256 points.
Use CC-Link remote I/O for 384 points.
...More relevant models >>>>
Name: PLC
Model: FX3U-48MR/DS
Max input / output points: 48 points.
Power supply voltage: 24VDC.
Input points: 24 points.
Output points: 24 points.
Output type: relay.
Power consumption: 35W.
Weight (kg):0.85.
Size (WxHxD) mm:182x90x86.
Built in CPU, power supply, input and output. By using a rich variety of functional extension boards and special adapters,
Can achieve high precision control.
Based on the function of FX2N has been greatly strengthened and enhanced.
High speed operation.
Basic instructions: 0.065 s/ instruction.
Application instruction: 0.642 s/ instruction.
Large capacity memory.
Built in program memory 64000 steps.
Flash memory cartridge with program transfer function.
Authentication。
Corresponding EN and UL/cUL authentication.
Faster and more efficient. Support high speed control and network communication, and have the function of data recording.
High speed, large capacity, multi-function high-end machine.
FX3U supports high speed processing, CC-Link communication, network communication, analog control and advanced positioning system.
Connected to the CC-Link, including the remote I/O, the maximum input and output control points up to 384 points,
Can correspond to a variety of field needs, the use of its scalability and flexibility to expand the scope of application of the control system.
Third generation high function micro programmable controller.
High speed, high efficiency, high performance, large capacity, and new features.
Built in high speed processing and positioning.
Control points: maximum 256 points.
Use CC-Link remote I/O for 384 points.
Output points: 16 points.
Output form: transistor.
Connected programmable logic controller: FX1NC, FX2NC, FX3UC.
Weight: 0.15KG.
FX2NC expansion module can be directly connected to the FX1NC, FX2NC, PLC FX3UC on the expansion of the input and output.
Do not need to connect the cable and so on, therefore can carry on the compact expansion MITSUBISHI FX3U-48MR/DS. Function: CPU module.
Input and output points: 32 points FX3U-48MR/DS
Power supply capacity (DC5V power): 720mA.
Power supply capacity (DC24V service power supply): 500mA.
Input / output mode: DC input (drain) / transistor (drain).
Input points: 16 points.
Output points: 16 points.
Expansion module is more compact, more suitable for small devices!
Small body on the collection of many functions MITSUBISHI FX3U-48MR/DS.
FX5UC can be connected to the expansion module, compact and convenient,
Suitable for all kinds of small equipment.
Through the rich conversion module,
Can freely connect FX5 and FX3 expansion devices. Specifications: FX0N-65EC.
Cable extending unit.
Length 65CM. Total points: 14 points.
Input points: 8 points.
Output points: 6 points.
Voltage: AC220V.
Output type: relay MITSUBISHI FX3U-48MR/DS.
Outline dimension: 60*75*90.
MITSUBISHI FX1S series PLC is suitable for the smallest package,
It is the preferred target for low cost users to seek powerful control over a limited range of I/0 MITSUBISHI PLC.
FX1S provides up to 30 I/O points, and can be transmitted through serial communication data,
MT models also have the ability to locate, widely used in a variety of small mechanical equipment MITSUBISHI PLC. Input signal: thermocouple type K or type J.
Applicable PLC:FX1N, FX2N, FX3U, FX2NC (to FX2NC-CNV-IF).
Applicable PLC:FX3UC (to FX2NC-CNV-IF or FX3UC-1PS-5V).
Thermocouple type temperature sensor input module.
Thermocouple type (K type, J type) temperature sensor input module MITSUBISHI PLC.
4 channels can be entered.
Unit can be set to Celsius or fahrenheit.
Resolution is K type 0.4 degree, J type 0.3 degree of high precision. Length: 1.5m.
Specification: FX round connector. Protocol: SLMP, TCP/IP, UDP.
Communication mode: full duplex / half duplex.
At the samme time can open a few: 4 connection FX3U-48MR/DS.
Weight: 0.3kg.
Connect PLC FX3U/FX3UC to Ethernet.
Support fixed buffer storage, communication connection MELSOFT, through the MC communication protocol, e-mail messages.
When connected tto the MELSOFT, through the Works2 PLC can achieve the remote maintenance of GX program MITSUBISHI FX3U-48MR/DS.
Connecting FX3UC, FX3GC requires FX2NC-CNV-IF or FX3UC-IPS-5V.
Output form: transistor.
Connected programmable logic controller: FX1NC, FX2NC, FX3UC.
Weight: 0.15KG.
FX2NC expansion module can be directly connected to the FX1NC, FX2NC, PLC FX3UC on the expansion of the input and output.
Do not need to connect the cable and so on, therefore can carry on the compact expansion MITSUBISHI FX3U-48MR/DS. Function: CPU module.
Input and output points: 32 points FX3U-48MR/DS
Power supply capacity (DC5V power): 720mA.
Power supply capacity (DC24V service power supply): 500mA.
Input / output mode: DC input (drain) / transistor (drain).
Input points: 16 points.
Output points: 16 points.
Expansion module is more compact, more suitable for small devices!
Small body on the collection of many functions MITSUBISHI FX3U-48MR/DS.
FX5UC can be connected to the expansion module, compact and convenient,
Suitable for all kinds of small equipment.
Through the rich conversion module,
Can freely connect FX5 and FX3 expansion devices. Specifications: FX0N-65EC.
Cable extending unit.
Length 65CM. Total points: 14 points.
Input points: 8 points.
Output points: 6 points.
Voltage: AC220V.
Output type: relay MITSUBISHI FX3U-48MR/DS.
Outline dimension: 60*75*90.
MITSUBISHI FX1S series PLC is suitable for the smallest package,
It is the preferred target for low cost users to seek powerful control over a limited range of I/0 MITSUBISHI PLC.
FX1S provides up to 30 I/O points, and can be transmitted through serial communication data,
MT models also have the ability to locate, widely used in a variety of small mechanical equipment MITSUBISHI PLC. Input signal: thermocouple type K or type J.
Applicable PLC:FX1N, FX2N, FX3U, FX2NC (to FX2NC-CNV-IF).
Applicable PLC:FX3UC (to FX2NC-CNV-IF or FX3UC-1PS-5V).
Thermocouple type temperature sensor input module.
Thermocouple type (K type, J type) temperature sensor input module MITSUBISHI PLC.
4 channels can be entered.
Unit can be set to Celsius or fahrenheit.
Resolution is K type 0.4 degree, J type 0.3 degree of high precision. Length: 1.5m.
Specification: FX round connector. Protocol: SLMP, TCP/IP, UDP.
Communication mode: full duplex / half duplex.
At the samme time can open a few: 4 connection FX3U-48MR/DS.
Weight: 0.3kg.
Connect PLC FX3U/FX3UC to Ethernet.
Support fixed buffer storage, communication connection MELSOFT, through the MC communication protocol, e-mail messages.
When connected tto the MELSOFT, through the Works2 PLC can achieve the remote maintenance of GX program MITSUBISHI FX3U-48MR/DS.
Connecting FX3UC, FX3GC requires FX2NC-CNV-IF or FX3UC-IPS-5V.
...More relevant models >>>>