LK Automation Limited
MITSUBISHI FX1S-20MR-DS Size (WxHxD) mm:75x90x49 PLC FX1S-20MR-DS
Brand:
MITSUBISHI
Name: PLC
Model: FX1S-20MR-DS
Max input / output points: 20 points.
Power supply voltage: 24VDC.
Input points: 12 points.
Output points: 8 points.
Output type: relay.
Power consumption (W): 7.
Weight (kg):0.3.
Size (WxHxD) mm:75x90x49.
Host has 10 points (6I/4O), 14 points (8I/6O), 20 points (12I/8O), 30 points (16I/14O) of 4 types.
This type of PLC is mainly used in all of the digital input, digital output control point of the device.
Can be directly connected to the 220V city power, built-in 8K step EEPROM memory, no battery, easy to maintain.
The series transistor output (MT) of the PLC, can be output 2 100KHz pulse, direct drive servo or stepper motor.
The series PLC can not be brought with the expansion module, but can be installed by the BD board to extend a small amount of I/O.
The series 1N through the installation of BD series PLC board, can achieve RS232, RS485, RS422 communication.
All equipment is digital input and output point.
The total I/O points are not more than 30 points, and the input points are less than 16, the output points are less than 14.
Its MT series of PLC can drive 2 way servo or stepper, commonly used in the control system for a simple manipulator.
...More relevant models >>>>
Name: PLC
Model: FX1S-20MR-DS
Max input / output points: 20 points.
Power supply voltage: 24VDC.
Input points: 12 points.
Output points: 8 points.
Output type: relay.
Power consumption (W): 7.
Weight (kg):0.3.
Size (WxHxD) mm:75x90x49.
Host has 10 points (6I/4O), 14 points (8I/6O), 20 points (12I/8O), 30 points (16I/14O) of 4 types.
This type of PLC is mainly used in all of the digital input, digital output control point of the device.
Can be directly connected to the 220V city power, built-in 8K step EEPROM memory, no battery, easy to maintain.
The series transistor output (MT) of the PLC, can be output 2 100KHz pulse, direct drive servo or stepper motor.
The series PLC can not be brought with the expansion module, but can be installed by the BD board to extend a small amount of I/O.
The series 1N through the installation of BD series PLC board, can achieve RS232, RS485, RS422 communication.
All equipment is digital input and output point.
The total I/O points are not more than 30 points, and the input points are less than 16, the output points are less than 14.
Its MT series of PLC can drive 2 way servo or stepper, commonly used in the control system for a simple manipulator.
Max input / output points: 14 points.
Supply voltage: 100 - 240VAC.
Input points: 8 points.
Output points: 6 points.
Output type: transistor.
Power consumption (W): 32.
Weight (kg):0.4.
Size (WxHxD) mm:90x90x75.
Rich functionality.
FX series of products are rich in variety, users can be based on cost or application,
Choose the most suitable product MITSUBISHI FX1S-20MR-DS. Will find a suitable model for the user site FX1S-20MR-DS
Terminal row type standard machine with extended input output
Can also be less of a system with analog or communication, etc..
CPU, power supply, input and output integration.
Display module or function expansion board can be less installed.
In addition, you can also reduce the input output or special module MITSUBISHI FX1S-20MR-DS.
Built in 8000 step EPROM memory.
No battery. Maintenance free.
Overseas oriented products meet all kinds of international standards. Total input and output points: 8 points.
Output points: 8 points.
Output type: transistor output.
FX Series in the compact body built in superior performance, and strive to operate simple.
In addition, rich options can meet the various needs of customers MITSUBISHI FX1S-20MR-DS.
In the virtual factory will be rich in the function of a part of the introduction.
It is easy to control the analog quantity of the application.
Can be extended to all models in the FX series analog devices MITSUBISHI PLC.
Function extension board, special adapter without programming can be used for communication.
FX2N extension module.
The expansion module is an input and output expansion device of the power supply from the basic unit or the expansion unit,
Can choose the relay or crystal output models, to 8 points for the unit to connect MITSUBISHI PLC.
Can be extended to FX3GA/FX3G, FX3GE, FX3GC, as well as FX3U, FX3UC series,
When connecting to FX3UC or FX3GC, you need FX2NC-CNV-IF or FX3UC-1PS-5V MITSUBISHI PLC.
The number of connection points depends on the basic unit and the expansion unit. Needle number: 20.
Specification: loose wire connector, 5 sets (0.3mm 2). Input points: 4 points.
Weight: 0.02kg.
Function expansion board is used in the FX3SA, FX3S, FX3GA, FX3G, FX3GE on thee small number of input and output extension of the product,
Can be built into PLC FX1S-20MR-DS. Memory format: EEPROM.
Number of steps: up to 2000 steps can be used.
Battery support: do not.
Method for writing and deleting: the device iss installed on the PLC, and is written and deleted by the peripheral device MITSUBISHI FX1S-20MR-DS.
Note: the built-in program transfer function (FX1S and FX1N host generic).
Supply voltage: 100 - 240VAC.
Input points: 8 points.
Output points: 6 points.
Output type: transistor.
Power consumption (W): 32.
Weight (kg):0.4.
Size (WxHxD) mm:90x90x75.
Rich functionality.
FX series of products are rich in variety, users can be based on cost or application,
Choose the most suitable product MITSUBISHI FX1S-20MR-DS. Will find a suitable model for the user site FX1S-20MR-DS
Terminal row type standard machine with extended input output
Can also be less of a system with analog or communication, etc..
CPU, power supply, input and output integration.
Display module or function expansion board can be less installed.
In addition, you can also reduce the input output or special module MITSUBISHI FX1S-20MR-DS.
Built in 8000 step EPROM memory.
No battery. Maintenance free.
Overseas oriented products meet all kinds of international standards. Total input and output points: 8 points.
Output points: 8 points.
Output type: transistor output.
FX Series in the compact body built in superior performance, and strive to operate simple.
In addition, rich options can meet the various needs of customers MITSUBISHI FX1S-20MR-DS.
In the virtual factory will be rich in the function of a part of the introduction.
It is easy to control the analog quantity of the application.
Can be extended to all models in the FX series analog devices MITSUBISHI PLC.
Function extension board, special adapter without programming can be used for communication.
FX2N extension module.
The expansion module is an input and output expansion device of the power supply from the basic unit or the expansion unit,
Can choose the relay or crystal output models, to 8 points for the unit to connect MITSUBISHI PLC.
Can be extended to FX3GA/FX3G, FX3GE, FX3GC, as well as FX3U, FX3UC series,
When connecting to FX3UC or FX3GC, you need FX2NC-CNV-IF or FX3UC-1PS-5V MITSUBISHI PLC.
The number of connection points depends on the basic unit and the expansion unit. Needle number: 20.
Specification: loose wire connector, 5 sets (0.3mm 2). Input points: 4 points.
Weight: 0.02kg.
Function expansion board is used in the FX3SA, FX3S, FX3GA, FX3G, FX3GE on thee small number of input and output extension of the product,
Can be built into PLC FX1S-20MR-DS. Memory format: EEPROM.
Number of steps: up to 2000 steps can be used.
Battery support: do not.
Method for writing and deleting: the device iss installed on the PLC, and is written and deleted by the peripheral device MITSUBISHI FX1S-20MR-DS.
Note: the built-in program transfer function (FX1S and FX1N host generic).
...More relevant models >>>>