LK Automation Limited
K2VU-S Series/K2VA-S Series Voltage relay series OMRON K2VU-S Series/K2VA-S Series The control power of the relay is not needed, which avoids the trouble of wiring
Brand:
OMRON
Name: Voltage relay series
Model: K2VU-S Series/K2VA-S Series
Static voltage relay.
K2VR-S/K2VA-S type, high action reliability disk with static type UVR/OVR.
Accurate work through high reliability semiconductor circuits.
Type K2VU-S1 is the output contact, but will be closed when the voltage is not enough,
Therefore, the locking time sequence circuit of the circuit breaker is not required.
Within the hidden from the start to the 2S timer, can easily adjust the time.
The control power of the relay is not needed, which avoids the trouble of wiring.
...More relevant models >>>>
Name: Voltage relay series
Model: K2VU-S Series/K2VA-S Series
Static voltage relay.
K2VR-S/K2VA-S type, high action reliability disk with static type UVR/OVR.
Accurate work through high reliability semiconductor circuits.
Type K2VU-S1 is the output contact, but will be closed when the voltage is not enough,
Therefore, the locking time sequence circuit of the circuit breaker is not required.
Within the hidden from the start to the 2S timer, can easily adjust the time.
The control power of the relay is not needed, which avoids the trouble of wiring.
Time specification: Inverse type.
Current setting range: 50 to 160 A.
Operating voltage: 100/110/120 VAC.
Resetting method: Manual.
Solid-state Relay Enables Choice of Three.
Operating Functions (Overcurrent, Open,
phase, and Reverse-phase).
Protects 3-phase induction motors and their loads from damage OMRON K2VU-S Series/K2VA-S Series.
Selection and combination of operating functions from overcur,
rent, open-phase, and reverse-phase K2VU-S Series/K2VA-S Series
Circuit and output relay operation can be checked by just operat,
ing the test button.
The set time value can be checked easily because operation time,
is indicated from the start of operation.
Space-saving, integrated construction.
Note: If the K2CM is used with an inverter, the operating conditions will,
depend on the load wiring length, inverter carrier frequency, basic,
frequency, and load conditions OMRON K2VU-S Series/K2VA-S Series. Error will occur in the operating,
values of the overload elements. It is recommended to test operation,
before using the K2CM. Model: PL (back-mounting), page 26, PCB terminals.
Approx: 10.8 g.
Number of pins: 11 pins.
A Wide Variety of Square and,
Round Sockets in Front-mounting,
and Back-mounting Models,
Models available with finger protection OMRON K2VU-S Series/K2VA-S Series.
Hold-down Clips and Socket Bridges for PYF Sockets,
are also available.
New screwless models available. Type: Multi-pole, Square Connector OMRON Voltage relay series.
Terminal Block: Terminal block with M3.5 screws.
Connector: Multi-pole, Square Connector Plugs *2.
No. of poles: 20.
Simplifies Connector and terminal,
block replacement, and requires less,
in-panel wiring OMRON Voltage relay series.
Mount to DIN Track or via screws.
MIL Flat Cable Connectors and Multi-pole, Square,
Connectors are standard.
Terminal blocks available with either M3 or M3.5 screws.
Connecting Cables for Programmable Controllers,
available (sold separately) OMRON Voltage relay series. Input voltage: DC10-60V.
Output current: 20 A.
Contribute to build high reliable systems.
Compact and Cost-effective solution.
for Back-up applications.
Easy setup for system reliability.
requirement.
Redundancy operating LED for the status confirmation.
A signal output for failure detection of power supplies.
By adjusting the power supply volttage to light up Balance LED,
the lifetime of power supplies will be more than twice K2VU-S Series/K2VA-S Series.
Wide range input.
DC5-30V (S8VK-R10), DC10-60V (S8VK-R20).
Wide operation temperature range: -40 to 70 °C.
Safety standards::
UL508/60950-1, CSA C22 OMRON K2VU-S Series/K2VA-S Series. 2 No. 107.1/60950-1.
EN50178, EN60950-1 Lloyd''s standards *2.
EMS: EN61000-6-2.
EMI: EN61000-6-3.
Six years warranty *3.
Current setting range: 50 to 160 A.
Operating voltage: 100/110/120 VAC.
Resetting method: Manual.
Solid-state Relay Enables Choice of Three.
Operating Functions (Overcurrent, Open,
phase, and Reverse-phase).
Protects 3-phase induction motors and their loads from damage OMRON K2VU-S Series/K2VA-S Series.
Selection and combination of operating functions from overcur,
rent, open-phase, and reverse-phase K2VU-S Series/K2VA-S Series
Circuit and output relay operation can be checked by just operat,
ing the test button.
The set time value can be checked easily because operation time,
is indicated from the start of operation.
Space-saving, integrated construction.
Note: If the K2CM is used with an inverter, the operating conditions will,
depend on the load wiring length, inverter carrier frequency, basic,
frequency, and load conditions OMRON K2VU-S Series/K2VA-S Series. Error will occur in the operating,
values of the overload elements. It is recommended to test operation,
before using the K2CM. Model: PL (back-mounting), page 26, PCB terminals.
Approx: 10.8 g.
Number of pins: 11 pins.
A Wide Variety of Square and,
Round Sockets in Front-mounting,
and Back-mounting Models,
Models available with finger protection OMRON K2VU-S Series/K2VA-S Series.
Hold-down Clips and Socket Bridges for PYF Sockets,
are also available.
New screwless models available. Type: Multi-pole, Square Connector OMRON Voltage relay series.
Terminal Block: Terminal block with M3.5 screws.
Connector: Multi-pole, Square Connector Plugs *2.
No. of poles: 20.
Simplifies Connector and terminal,
block replacement, and requires less,
in-panel wiring OMRON Voltage relay series.
Mount to DIN Track or via screws.
MIL Flat Cable Connectors and Multi-pole, Square,
Connectors are standard.
Terminal blocks available with either M3 or M3.5 screws.
Connecting Cables for Programmable Controllers,
available (sold separately) OMRON Voltage relay series. Input voltage: DC10-60V.
Output current: 20 A.
Contribute to build high reliable systems.
Compact and Cost-effective solution.
for Back-up applications.
Easy setup for system reliability.
requirement.
Redundancy operating LED for the status confirmation.
A signal output for failure detection of power supplies.
By adjusting the power supply volttage to light up Balance LED,
the lifetime of power supplies will be more than twice K2VU-S Series/K2VA-S Series.
Wide range input.
DC5-30V (S8VK-R10), DC10-60V (S8VK-R20).
Wide operation temperature range: -40 to 70 °C.
Safety standards::
UL508/60950-1, CSA C22 OMRON K2VU-S Series/K2VA-S Series. 2 No. 107.1/60950-1.
EN50178, EN60950-1 Lloyd''s standards *2.
EMS: EN61000-6-2.
EMI: EN61000-6-3.
Six years warranty *3.
...More relevant models >>>>
Related download