LK Automation Limited
HC-MF13 Using a serial absolute / incremental encoder MITSUBISHI HC-MF13 Universal interface driver
Brand:
MITSUBISHI
Name: Ultra low inertia small capacity motor
Model: HC-MF13
Motor series: ultra low inertia, small capacity.
Using a serial absolute / incremental encoder.
Rated output power: 0.1kw.
Rated speed: 3000rpm.
With the brake: not with brake.
Without GB.
Shaft end: straight shaft.
The rotor of the servo motor is a permanent magnet, and the control of the servo amplifier is controlled by the U/V/W three-phase electric electromagnetic field,
The rotor rotates under the action of the magnetic field, and the encoder feedback signal of the motor is given to the driver,
According to the feedback value and the target value, the driver is compared,
Adjust the rotor rotation angle.
The accuracy of the servo motor is determined by the resolution of the encoder.
...More relevant models >>>>
Name: Ultra low inertia small capacity motor
Model: HC-MF13
Motor series: ultra low inertia, small capacity.
Using a serial absolute / incremental encoder.
Rated output power: 0.1kw.
Rated speed: 3000rpm.
With the brake: not with brake.
Without GB.
Shaft end: straight shaft.
The rotor of the servo motor is a permanent magnet, and the control of the servo amplifier is controlled by the U/V/W three-phase electric electromagnetic field,
The rotor rotates under the action of the magnetic field, and the encoder feedback signal of the motor is given to the driver,
According to the feedback value and the target value, the driver is compared,
Adjust the rotor rotation angle.
The accuracy of the servo motor is determined by the resolution of the encoder.
1 axis servo amplifier.
MITSUBISHI general AC servo amplifier MELSERVO-J4 series.
Rated output: 12.0kw.
Interface: SSCNET III /H.
Power supply: three phase AC400V.
0.6kW and 1kW above the servo amplifier.
Servo amplifier supporting SSCNET III /H.
Complete synchronization system capable of using high speed serial optical communication MITSUBISHI HC-MF13.
Can be combined with the servo system controller to maximize the performance of the servo system HC-MF13
The industry''s top level speed motor, the frequency of 2.5kHz amplifier, and optical fiber network extradimensional Symphony orchestra.
Using the traditional two degree of freedom model adaptive control to further optimize the exclusive high speed servo control structure of the dedicated execution engine MITSUBISHI HC-MF13.
Achieved the fastest 2.5kHz speed frequency response in the industry.
Combined with MITSUBISHI independent research and development of high resolution absolute position encoder (4194304pulses/rev),
Greatly improve the processing speed. Can maximize the performance of high-end machinery. The length of the line: 10m.
IP level: IP67.
Bending life: high bending life MITSUBISHI HC-MF13.
Encoder cable for HF-KP/HF-MP/HF-SP/HF-JP/HC-LP/HC-UP series. Motor series: medium inertia, medium power.
Rated output power: 0.5kw.
Rated speed: 2000r/min.
Whether to bring the brakes: with.
Shaft end: Standard (straight).
Power supply: 400V type.
Protection level: IP65 (IP67) MITSUBISHI Universal interface driver.
Features: medium inertia from low speed to high speed three modes for selection, suitable for different applications MITSUBISHI Universal interface driver.
Application examples: transmission machinery, robots, X-Y working platform.
High resolution encoder 131072p/rev (17 bit).
The encoder with high resolution ensures excellent performance and stability at low speed.
All motor dimensions are the same as before and all are compatible with the wiring MITSUBISHI Universal interface driver. MITSUBISHI motor universal AC servo amplifier MELSERVO-J3 series.
Rated output: 11.0kw.
Interface type: CC-Link communication type (built-in positioning function).
Power specification: three phase AC200V.
Positioning operation by setting position and rotational speed data in the positioning table and receiving the start signal from the main controller.
The setting of the position and speed of the positioning table, as well as the start and stop operation can be completed through CC-Link communication.
By using the MR-J3-D01 extension IO unit, the DI/O instruction can be used to select and locate the table.
(CC-Link can not be used for MR-J3-D01 communications).
With built-in positioning function of the servo amplifier, can be set through the CC-Link communications and speed data. (corresponding to the CC-Link version: Ver.1.10)
Can be achieved through the CC-Link communications to start, stop and monitoring and otherr operations HC-MF13.
Serial communication reduce wiring.
Distributed servo control system can be built by CC-Link communication.
The parameters of unit MR-PRU03 (optional) the parameter setting, operation and monitoring more convenient.
The servo amplifier can be used for speed control operation MITSUBISHI HC-MF13.
When the two stations are occupied, the speed can be set directly by the remote register.
MITSUBISHI general AC servo amplifier MELSERVO-J4 series.
Rated output: 12.0kw.
Interface: SSCNET III /H.
Power supply: three phase AC400V.
0.6kW and 1kW above the servo amplifier.
Servo amplifier supporting SSCNET III /H.
Complete synchronization system capable of using high speed serial optical communication MITSUBISHI HC-MF13.
Can be combined with the servo system controller to maximize the performance of the servo system HC-MF13
The industry''s top level speed motor, the frequency of 2.5kHz amplifier, and optical fiber network extradimensional Symphony orchestra.
Using the traditional two degree of freedom model adaptive control to further optimize the exclusive high speed servo control structure of the dedicated execution engine MITSUBISHI HC-MF13.
Achieved the fastest 2.5kHz speed frequency response in the industry.
Combined with MITSUBISHI independent research and development of high resolution absolute position encoder (4194304pulses/rev),
Greatly improve the processing speed. Can maximize the performance of high-end machinery. The length of the line: 10m.
IP level: IP67.
Bending life: high bending life MITSUBISHI HC-MF13.
Encoder cable for HF-KP/HF-MP/HF-SP/HF-JP/HC-LP/HC-UP series. Motor series: medium inertia, medium power.
Rated output power: 0.5kw.
Rated speed: 2000r/min.
Whether to bring the brakes: with.
Shaft end: Standard (straight).
Power supply: 400V type.
Protection level: IP65 (IP67) MITSUBISHI Universal interface driver.
Features: medium inertia from low speed to high speed three modes for selection, suitable for different applications MITSUBISHI Universal interface driver.
Application examples: transmission machinery, robots, X-Y working platform.
High resolution encoder 131072p/rev (17 bit).
The encoder with high resolution ensures excellent performance and stability at low speed.
All motor dimensions are the same as before and all are compatible with the wiring MITSUBISHI Universal interface driver. MITSUBISHI motor universal AC servo amplifier MELSERVO-J3 series.
Rated output: 11.0kw.
Interface type: CC-Link communication type (built-in positioning function).
Power specification: three phase AC200V.
Positioning operation by setting position and rotational speed data in the positioning table and receiving the start signal from the main controller.
The setting of the position and speed of the positioning table, as well as the start and stop operation can be completed through CC-Link communication.
By using the MR-J3-D01 extension IO unit, the DI/O instruction can be used to select and locate the table.
(CC-Link can not be used for MR-J3-D01 communications).
With built-in positioning function of the servo amplifier, can be set through the CC-Link communications and speed data. (corresponding to the CC-Link version: Ver.1.10)
Can be achieved through the CC-Link communications to start, stop and monitoring and otherr operations HC-MF13.
Serial communication reduce wiring.
Distributed servo control system can be built by CC-Link communication.
The parameters of unit MR-PRU03 (optional) the parameter setting, operation and monitoring more convenient.
The servo amplifier can be used for speed control operation MITSUBISHI HC-MF13.
When the two stations are occupied, the speed can be set directly by the remote register.
...More relevant models >>>>