E32-T12F type: resistant to environmental type; resistant to drugs,
Specialty: Teflon coating for long distance,
Shape / detection distance (mm): 4000; 3000; 2000 (800),
Bending radius (mm): R40.
Standard test object (minimum test object) (mm) 1: 4 (0.1),
Fiber element for meeting diversified needsType of input: AC voltage input E5CN-HQ2H03-W-FLK AC100-240.
Output type: communication; RS-232C; NPN open collector (HH, H, PASS, L, LL) E5CN-HQ2H03-W-FLK AC100-240
Event input terminal 5 points (TIMING, S-TIM, HOLD, RESET, ZERO) is equipped with.
External supply 80mA DC12V.
Power supply voltage: AC/DC24V.
96 (W) * 48 (H * 95mm) depth
Some models are not equipped with E5CN-HQ2H03-W-FLK AC100-240.
The most suitable voltage and current signal simulation, measurement and display, identification of the panel table .
Action determine the color, can switch the green / Red 2 kinds of color display.
Equipped with the sub pressure gauge for monitoring the operation trend.
External event input can be applied to a variety of measurement and identification situations E5CN-HQ2H03-W-FLK AC100-240.
DeviceRelease key type: Special release key.
Indicator: Green.
Lock and release types: Mechanical lock Solenoid release .
Contact configuration(door open/closed detection switch,
and lock monitor switch contacts): 3NC+2NC/1NO.
Conduit opening: M20.
Holding Force of 3,000 N.
Two safety circuits and two monitor contacts provide an,
array of monitoring patterns.
Standard gold-clad contacts enable use with ordinary loads,
and microloads.
Models with trapped keys prevent workers from being locked,
in hazardous work areas.
Models with rear release buttons allow people to unlock the,
Switch and escape if they are locked into hazardous areas.
IP67 degree of protection. Size: 96 x 96mm.
Category: power AC100 ~ 240V with.
Shell color: black.
Control output 1: output unit mode.
Control output 2: output unit mode.
Control mode: standard or heating cooling.
Auxiliary output points: 2 points.
Heater break, SSR fault detection function: single phase or three phase heater detection function.
Event entry point: 4.
Transfer output: transfer output (special terminal).
Remote SP:4 to 20mA input.
Communication: -.
New program type.
A new type of liquid crystal with high performance cost ratio is adopted in the 256 paragraph,
Visual angle, contrast can be improved.
Can be set up to 8 procedures (mode) x 32 (step) procedure.
High resolution 5 bit display / can display 0.01 degrees C.
High speed sampling period 60ms.
All models complete a variety of (to the thermocouple /Pt/ analog input switching), 1 machines to support a variety of sensors.
Also supports remote SP.
Add PV/SV state display function, to see the state of the thermostat
(automatic / manual, RUN/RESET, alarm), interactive display PV/SV.
Through the support software (VVer .4.3 CX-Thermo) makes the process of setting management becomes very
Simple use of simple computing functions (AND/OR logic and delay) to set the implementation of flexible contact output OMRON E5CN-HQ2H03-W-FLK AC100-240.
Through the infrared port can be carried out from the frronnt of the communication OMRON E5CN-HQ2H03-W-FLK AC100-240.
The control output ON/OFF times counting function can predict the fault of the internal relay of the temperature controller.
E5CN-HQ2H03-W-FLK AC100-240 Operation manual/Instructions/Model selection sample download link: /searchDownload.html?Search=E5CN-HQ2H03-W-FLK AC100-240&select=5