Servo motor series: ultra low inertia, small capacity.
Rated output: 0.1kw.
Rated speed: 3000r/min.
Electromagnetic brake: incidental.
Power supply: 200V.
The rated speed is 3000r/min, the maximum speed is 6000r/min.
The maximum torque of 350% of the rated torque, high torque in the field of high rotation, only to support the HG-KR series products MITSUBISHI .
Built in absolute position encoder with high resolution
HC-RF153
Standard high resolution absolute position encoder (4194304p/rev (22bit)).
To achieve a higher accuracy of the positioning function.
Improve the environmental performance of HG-KR, HG-MR, HG-RR, HG-UR series of products using IP65 MITSUBISHI . Max input / output points: 30 points.
Supply voltage: 100 - 240VAC .
Input points: 16 points.
Output points: 14 points.
Output type: relay.
Power consumption (W): 21.
Weight (kg):0.45.
Size (WxHxD) mm:100x90x75.
Host has 10 points (6I/4O), 14 points (8I/6O), 20 points (12I/8O), 30 points (16I/14O) of 4 types.
This type of PLC is mainly used in all of the digital input, digital output control point of the device MITSUBISHI .
Can be directly connected to the 220V city power, built-in 8K step EEPROM memory, no battery, easy to maintain .
The series transistor output (MT) of the PLC, can be output 2 100KHz pulse, direct drive servo or stepper motor.
The series PLC can not be brought with the expansion module, but can be installed by the BD board to extend a small amount of I/O.
The series 1N through the installation of BD series PLC board, can achieve RS232, RS485, RS422 communication. Power supply: 110mA DC5V (PLC internal power supply), 80mA DC24V (through the power connector by the external power supply).
Analog input points: 4 points.
Voltage input: DC-10~10V.
Current input: DC-20~20mA, 4~20mA.
Weight: 0.2kg.
Dimensions: 55 x 90 x 87.
Voltage input and current input of 4 channels can be carried out,
Each channel can be specified as a current input or voltage input.
Built in digital filter function and peak hold function, etc.,
Achieved a high speed of 500 AD S/ch conversion.
FX3UC-4AD can be connected to the FX3GC or FX3UC series. Type: MR-J_B series.
Rated output: 0.6KW.
Interface: standard.
Servo system according to the system structure can be divided into open loop servo system, closed loop servo system, semi closed loop system, compound control system.
The closed loop automatic control system with feedback is composed of a position detecting part, a deviation amplifying part, an executing part and a controlled object.
Servo system must have good controllability, high stability and high adaptability.
Note that the control of the signal is good after the disappearance of the signal, can immediately stop the turn;
High stability is the torque with the increase of speed and uniform decline; adaptability is fast, sensitive, and ring state quality is good.
According to the types of servo drives are classified, there are three kinds of electric, hydraulic or electric hydraulic.
If the servo system is divided according to tthe function, then theree is a measuring servo and power servo system;
Analog servo and power servo system; position servo and acceleration servo system MITSUBISHI HC-RF153.
The electric servo system can be divided into two categories: DC DC servo system and AC AC servvo system based on the electrical signals MITSUBISHI HC-RF153.
AC AC servo system also has two kinds of asynchronous motor servo system and synchronous motor servo system.
HC-RF153 Operation manual/Instructions/Model selection sample download link:
/searchDownload.html?Search=HC-RF153&select=5