LK Automation Limited LK Automation Limited
Brand Sort: OMRON | MITSUBISHI | Proface | Mennekes | Yaskawa
Home >> Price
MITSUBISHI HC-MFS053D
MITSUBISHI HC-MFS053D
Power: 0.4kw.
Purpose: high frequency braking resistor.
The use rate of the built-in regenerative brake of the transducer can be promoted.
When using the FR-ABR type brake resistor, the short circuit piece between the terminal PR-PX is removed. Does not remove the short circuit chip will lead to overheating of the brake resistor MITSUBISHI .
The utilization rate of the regenerative braking should be less than the allowable brake use rate in the above table HC-MFS053D
With the operating frequency of the brake resistor to reach 300 degrees C or higher, it is necessary to take protective measures and cooling.
MYS type resistor can be used. But please pay attention to the allowable brake use rate MITSUBISHI .
Do not remove the terminal P/+ and P1 between the short circuit chip, in addition to connecting the DC reactor .
The installation of thermal relay, to avoid overheating and burn the braking resistor. MITSUBISHI inverter series: FR-F840.
Voltage level: three phase 400V.
Power: 11kw.
SLD converter rated current: 25.0A.
Structure and function: Standard model MITSUBISHI .
Type: CA.
Substrate coating: have.
2 times the power consumption of the wind turbine and pump and the speed of the 3 power consumption is proportional to the speed of the rotating speed .
Through the speed control of the frequency converter to adjust the air flow, can reduce the power consumption.
Give full play to the performance of the motor.
The excitation current is always adjusted to the best state, which can improve the efficiency of the motor.
Load torque is smaller, can further improve energy efficiency.
For example, when a general motor is used, the optimal excitation control mode in the 4% motor load torque is about 30% more than that of the V/F control. "MITSUBISHI general purpose AC servo amplifier MELSERVO-J2-Super series.
Rated output: 7.0kw.
SSCNET interface.
Voltage: 3 phase AC400V.
Complete synchronization system with SSCNET high speed serial communication,
The communication cycle between the controller and the servo amplifier is the longest 0.888ms.
Such systems will be able to provide high reliability and high performance.
When connecting the servo system with SSCNET,
In the motion system, the parameters of the servo amplifier and the acquisition of the data will be displayed on the motion controller.
Connect a dedicated cable with an amplifier and a controller to form a SSCNET system.
This ssimple connection method rreduces the routing time and helps to prevent noise MITSUBISHI HC-MFS053D.
Even in the MELSERVO-J2-SUPER series products using high resolution coding standards, the command frequency is no limit.
It is only necessary to add a battery on the servvo amplifier, which can form the absolute value system MITSUBISHI HC-MFS053D.
Currently there are more than 1000000 high reliability SSCNET servo amplifier networks in use. "
HC-MFS053D Operation manual/Instructions/Model selection sample download link: /searchDownload.html?Search=HC-MFS053D&select=5


...more relevant model market price >>>>
Related products
MITSUBISHI
Ultra low inertia small power motor
HC-MFS73
MITSUBISHI Ultra low inertia small power motor HC-MFS73
Motor series: ultra low inertia, low pow
MITSUBISHI
Ultra low inertia small power motor
HC-MFS053BK
MITSUBISHI Ultra low inertia small power motor HC-MFS053BK
Motor series: ultra low inertia, low pow
MITSUBISHI
Ultra low inertia small power motor
HC-MFS43K
MITSUBISHI Ultra low inertia small power motor HC-MFS43K
Motor series: ultra low inertia, low pow
MITSUBISHI
Ultra low inertia small power motor
HC-MFS13BD
MITSUBISHI Ultra low inertia small power motor HC-MFS13BD
Motor series: ultra low inertia, low pow