LK Automation Limited LK Automation Limited
Brand Sort: OMRON | MITSUBISHI | Proface | Mennekes | Yaskawa
Home >> Price
HF-SE52 MITSUBISHI HF-SE52
MITSUBISHI HF-SE52
Motor series: low inertia, small capacity.
Using a serial absolute / incremental encoder.
Rated output power: 0.3kw.
Rated speed: 3000rpm.
With a brake band.
Shaft end: straight shaft.
AC servo motor and brushless DC servo motor in the function of the difference: AC servo is better, because it is a sine wave control, torque ripple small MITSUBISHI HF-SE52.
DC servo is a trapezoidal wave. DC servo is simple and cheap HF-SE52 Input points: 32 points.
Output points: 32 points.
Output form: transistor.
Connected programmable logic controller: FX1NC, FX2NC, FX3UC.
FX2NC expansion module can be directly connected to the FX1NC, FX2NC, PLC FX3UC on the expansion of the input and output MITSUBISHI HF-SE52.
Do not need to connect the cable and so on, therefore can carry on the compact expansion . 2 channel.
Input: DC4~20mA (connecting two wire transmitter); DC0~20mA.
Output (resolution): 0~4000. 0~12000.
Conversion speed: 10ms/ channel.
40 pin connector.
Isolation between channels.
Power supply to a two wire transmitter.
The possibility of expanding control with intelligent function MITSUBISHI HF-SE52.
At the same time, the channel isolation analog module realizes high isolation voltage,
Further improve the accuracy of the benchmark .
Provide support for process control using a general purpose programmable controller.
Flow meter, pressure meter, other sensors can be directly connected to analog input,
Control valve can also be directly connected to analog output.
Hardware and installation costs have been greatly reduced due to the need for an external isolation amplifier.
High insulation strength.
Can isolate electrical interference, such as current and noise, etc..
Standard analog input module.
Isolated analog input module.
No external isolation amplifier required.
Without the use of inter channel isolation analog modules.
Using the inter channel isolation analog module.Optional features of memory card (A/FX compatible).
1MB extended memory.
Applicable models: A985 (-V) /975/970/A960GOT (-B) /A956WGOT. MITSUBISHI motor universal AC servo amplifier MELSERVO-J3 series.
Rated output: 2.0kw.
Interface type: CC-Link communication type (built-in positioning function).
Power specification: three phase AC400V.
Positioning operation by setting position and rotational speed data in the positioning table and receiving the start signal from the main controller.
The setting of the position and speed of the positioning table, as well as the start and stop operation can be completed through CC-Link communication.
By using the MR-J3-D01 extension IO unit, the DI/O instruction can be used to select and locate the table.
(CC-Link can not be used for MR-J3-D01 communications).
With built-in positioning function of the servo amplifier, can be set through the CC-Link communications and speed data. (corresponding to the CC-Link version: Ver.1.10)
Can be achieved through the CC-Link communications to start, stop and moonitoring annd other operations HF-SE52.
Serial communication reduce wiring.
Distributed servo control system can be built by CC-Link communication.
The parameters of unit MR-PRU03 (optional) the parameter setting, operation and monitoring more convenient.

Thhe servo amplifier can be used for speed control operation HF-SE52.
When the two stations are occupied, the speed can be set directly by the remote register.
HF-SE52 Operation manual/Instructions/Model selection sample download link: /searchDownload.html?Search=HF-SE52&select=5


...more relevant model market price >>>>
Related products
MITSUBISHI
servo motor
HF-KE73BJW1-S100
MITSUBISHI servo motor HF-KE73BJW1-S100
Type: HF-KE servo motor, low inertia, lo
MITSUBISHI
Medium inertia power servo motor
HF-SP201
MITSUBISHI Medium inertia power servo motor HF-SP201
Servo motor series: medium inertia, medi