MITSUBISHI inverter series: FR-A800.
Voltage level: three phase 400V.
Power: 355kw.
SLD converter rated current: 866A.
Structure and function: the rectification part is off type.
Type: CA.
Substrate coating: have.
To maximize the performance of the motor.
Advanced auto tuning function.
The newly developed PM motor auto tuning feature can be used to operate other manufacturers of PM motors (Yong Ci synchronous motors) in the sensorless state HC-SFS152BG1 1/43
Not only can drive MITSUBISHI induction motor and PM motor, but also can drive other manufacturers of induction motor and PM motor.
This means that you can reduce the cost of inventory and supplies MITSUBISHI HC-SFS152BG1 1/43.
If the PM motor is produced by a IPM motor or other company using MM-CF, the starting torque is limited to 50%,
Even after tuning is not simple to use and positioning control of zero speed torque) induction motor and permanent magnet motor can be combined freely . Analog channel: 8 channels.
Input / output (resolution): 0 ~ 4000.
Conversion speed: 100ms/8 channel MITSUBISHI HC-SFS152BG1 1/43.
Analog module installation.
Power supply: AC170V ~ 264V.
According to the control requirements of the system, using the appropriate design method to design MITSUBISHI PLC program .
Procedures to meet the requirements of system control as the main line,
Write one by one to achieve the control function or the sub task of the program,
Gradually improve the functions specified by the system.
MITSUBISHI PLC detection, fault diagnosis and display and other procedures.
These procedures are relatively independent, generally in the basic completion of the program design and then add.
Hardware simulation method is to use a number of hardware equipment to simulate the generation of the signal,
The signals are connected to the input end of the PLC system in a hard wired way, and the timeliness is strong.
Software simulation method is in the MITSUBISHI PLC in the preparation of a set of simulation program,
The simulation provides the field signal, which is simple and easy to operate, but it is not easy to guarantee the timeliness.
Simulation of the process of debugging, debugging method can be used to segment, and the monitoring function of programmer. "Maximum control axis: 16 axis.
Connection mode with servo amplifier: IE CC-Link field network connection type.
The maximum distance between the drive units: 100m.
Operation cycle: 0.88ms, 1.77ms, 3.55ms.
Interpolation function: linear interpolation (maximum 4 axis), 2 axis arc interpolation.
Color signal: 4 points.
Color detecting set: 16 set.
Motion control into CC-LinkIE network.
Positioning control, synchronization control and cam control can be easily carried out by the simple parameter setting and the starting of the sequential program.
QD77GF can be used as the main station of CC-LinkIE network.
Communication between 1 network implementation and servo amplifier, field device (remote I/O, sensor, etc.).
Note 1:QD77G only the master station can use the bus shape, star. 1 networks can connect up to 104 units from the device.
Even the long distance wiring can be flexible.
The use of fiber optic cable, with high speed, high performance, high reliability of the servo system controller network.
In addition to the traditional positioning control, but also to support speed / torque control and synchronous control.
Use simple movement module setup tool",
Can easily perform positioning settings, monitoring and debugging, etc..
In addition, the data can be collected and displaayed synchronously witth the motion controller HC-SFS152BG1 1/43.
Support comprehensive, wiring flexible IE CC-Link field network.
This module can be used as the main station of IE CC-Link field network (equivalent to QJ71GF11-T2),
And still retains the function of ssimmple motion module HC-SFS152BG1 1/43.
Therefore, flexible connection display (GOT), remote I/O, frequency converter and other equipment, flexible construction system. "
HC-SFS152BG1 1/43 Operation manual/Instructions/Model selection sample download link: /searchDownload.html?Search=HC-SFS152BG1 1/43&select=5