LK Automation Limited LK Automation Limited
Brand Sort: OMRON | MITSUBISHI | Proface | Mennekes | Yaskawa
Home >> Price
MITSUBISHI FX2N-16SW Price FX2N-16SW
MITSUBISHI FX2N-16SW
Servo motor series: flat type, medium capacity.
Rated output: 2.0kw.
Rated speed; 2000r/min.
Electromagnetic brake: No.
Power supply: 200V.
The most suitable medium capacity, flat type products to limit the installation space of the situation.
Improve the environmental performance of HG-KR, HG-MR, HG-RR, HG-UR series of products using IP65 FX2N-16SW Price.
100 scene, there are 100 different drive control.
In order to meet the needs of the diverse and detailed field,
MR-J4 product line configuration, providing a wealth of servo amplifier and servo motor products FX2N-16SW
Can meet the different needs of different customers. Power: 3.7kw.
Purpose: high frequency braking resistor FX2N-16SW Price.
The use rate of the built-in regenerative brake of the transducer can be promoted .
When using the FR-ABR type brake resistor, the short circuit piece between the terminal PR-PX is removed. Does not remove the short circuit chip will lead to overheating of the brake resistor.
The utilization rate of the regenerative braking should be less than the allowable brake use rate in the above table FX2N-16SW Price.
With the operating frequency of the brake resistor to reach 300 degrees C or higher, it is necessary to take protective measures and cooling .
MYS type resistor can be used. But please pay attention to the allowable brake use rate.
Do not remove the terminal P/+ and P1 between the short circuit chip, in addition to connecting the DC reactor.
The installation of thermal relay, to avoid overheating and burn the braking resistor. Input type: DC input, positive common end.
Input points: 16 points.
Enter the response time: 1.5ms the following.
Rated input voltage / current: DC24V/5mA.
External connection: 4 wire.
Fast connector type.
Simple wiring through quick connector.
Can be installed along the 6 direction.
MITSUBISHI PLC program simulation debugging
The basic idea of program simulation debugging is,
In order to facilitate the form of simulation to generate the actual state of the scene,
Create the necessary environmental conditions for the operation of the program.
Depending on the way the field signals are generated,
The simulation debugging has two forms of hardware simulation and software simulation. Output points: 16 points.
Output voltage and current: DC12~24V; 0.5A/ point; 4A/ common.
OFF leakage current: 0.1mA.
Response time: 1ms.
16 points and 1 common ends.
Source type.
18 point spring clip connection terminal.
With the surge absorber.
With fuse.
Ultra high speed processing, production time is shortened, better performance.
As applications become larger and more complex, it is necessary to shorten the system operation cycle time.
The operation period can be shortened by the super high basic operation speed 1.9ns.
In addition to achieve in the past with the control of single-chip high-speed control,
The system performance can be improved by reducing the total scan time,
To prevent any possible performance bias.
Convenient processing of large capacity data.
In the past can not achieve the standard RAM and SRAM card file register area of continuous access,
The boundary of each area should be considered in programming.
The SRAM 8MB extension card is installed in the high speed universal QCPU,
Standard RAM can be used as a continuous file register,
Capacity up to 4736K words, thus simplifying the programming.
Thus, even if the memory space of the soft element is insufficient,
Can also be installed by the expansion of SRAM card, easy to extend the file register area.
The address register is extended to 32 bits, which can be programmed to go beyond the traditional 32K word,
And to achieve the extension to the file register to all regions of the file register.
In addition, the processing speed of the index modification plays an important role in the efficient operation of structured data (array),
The speed has been improved.
When the index is used to modify the program repeatedly (e.g. from FOR to NEXT), the scan time can be reduced.
With the help of sample tracking function, the starting time is shortened
By using the sampling and tracking function, it is convenient to analyze the data when the fault occurs,
Testing procedures for the time, etc., can shorten the time of failure analysis and start-up time.
In addition, the multi CPU system also helps to determine the data transsceiver time between the CPU module MITSUBISHI FX2N-16SW.
Can be used to analyze the data collected by programming tools,
In the form of charts and trend charts, the data changes of the bit soft element and the word soft element can be easily diispplayed MITSUBISHI FX2N-16SW.
And the sampling tracking results can be stored in LogViewer GX form CSV,
By recording data display and analysis tool LogViewer GX to display.
FX2N-16SW Operation manual/Instructions/Model selection sample download link: /searchDownload.html?Search=FX2N-16SW&select=5


...more relevant model market price >>>>
Related products
MITSUBISHI
CC-Link interface module
FX2N-32CCL
MITSUBISHI CC-Link interface module FX2N-32CCL
CC-Link interface module. PLC FX can e
MITSUBISHI
Connecting cable
FX2NC-100MPCB
MITSUBISHI Connecting cable FX2NC-100MPCB
Use: power cord for asic unit. Length:
MITSUBISHI
PLC
FX2N-64MT-001
MITSUBISHI PLC FX2N-64MT-001
Max input / output points: 64 points. Su
MITSUBISHI
output module
FX2NC-16EYR-T
MITSUBISHI output module FX2NC-16EYR-T
Function: terminal output. Output points