LK Automation Limited LK Automation Limited
Download Sort: OMRON | MITSUBISHI | Proface | Mennekes | Yaskawa
Catalog Download >> FX3GA-60MR-CM
MITSUBISHI FX3GA-60MR-CM PDF datasheet PLC datasheet PDF catalog
Product model: FX3GA-60MR-CM
Name: PLC
Brand: MITSUBISHI
Sort: PDF datasheet
File language: English
Protocol: SLMP, TCP/IP, UDP.
Communication mode: full duplex / half duplex.
At the same time can open a few: 4 connection.
Weight: 0.3kg.
Connect PLC FX3U/FX3UC to Ethernet.
Support fixed buffer storage, communication connection MELSOFT, through the MC communication protocol, e-mail messages.
When connected to the MELSOFT, through the Works2 PLC can achieve the remote maintenance of GX program FX3GA-60MR-CM PDF catalog FX3GA-60MR-CM
Connecting FX3UC, FX3GC requires FX2NC-CNV-IF or FX3UC-IPS-5V. Can be isolated to obtain DC24/48/100V, AC100/200V input signal.MITSUBISHI inverter series: FR-F840.
Voltage level: three phase 400V.
Power: 22.0kw.
SLD converter rated current: 47A.
Structure and function: Standard model.
Type: CA.
Substrate coating: have FX3GA-60MR-CM PDF catalog.
2 times the power consumption of the wind turbine and pump and the speed of the 3 power consumption is proportional to the speed of the rotating speed.
Through the speed control of the frequency converter to adjust the air flow, can reduce the power consumption.
Give full play to the performance of the motor.
The excitation current is always adjusted to the best state, which can improve the efficiency of the motor FX3GA-60MR-CM PDF catalog.
Load torque is smaller, can further improve energy efficiency.
For example, when a general motor is used, the optimal excitation control mode in the 4% motor load torque is about 30% more than that of the V/F control MITSUBISHI PLC PDF catalog. The largest input / output points: 20 points.
Power supply voltage: 24VDC.
Input points: 12 points.
Output points: 8 points MITSUBISHI PLC PDF catalog.
Output type: Transistor (source).
Power consumption (W): 7.
Weight (kg):0.3.
Size (WxHxD) mm:75x90x49.
All equipment is digital input and output point.
The total I/O points are not more than 30 points, and the input points are less than 16, the output points are less than 14.
Its MT series of PLC can drive 2 way servo or stepper, commonly used in the control system for a simple manipulator MITSUBISHI PPLC PDF catalog FX3GA-60MR-CM PDF datasheet.
MITSUBISHI FX1S series PLC is suitable for the smallest package,
It is the preferred target for low cost users to seek powerful control over a limited range of I/0.
FX1S provides up to 30 I/O points, and ccan be transmitted through serial communication data,
MT models also have the ability to locate, widely used in a variety of small mechanical equipment FX3GA-60MR-CM PDF catalog.
Related products
MITSUBISHI
PLC
FX3SA-20MR-CM
MITSUBISHI PLC FX3SA-20MR-CM
Input and output points: 20 points. Powe
MITSUBISHI
PLC
FX3SA-10MR-CM
MITSUBISHI PLC FX3SA-10MR-CM
Input and output points: 10 points. Powe
MITSUBISHI
PLC
FX3GA-60MT-CM
MITSUBISHI PLC FX3GA-60MT-CM
Input and output points: 60 points. Powe
MITSUBISHI
PLC
FX3GA-24MR-CM
MITSUBISHI PLC FX3GA-24MR-CM
Input and output points: 24 points. Powe