LK Automation Limited LK Automation Limited
Download Sort: OMRON | MITSUBISHI | Proface | Mennekes | Yaskawa
Catalog Download >> FX3U-32BL
FX3U-32BL PDF datasheet MITSUBISHI FX3U-32BL datasheet PDF catalog
Product model: FX3U-32BL
Name: Battery
Brand: MITSUBISHI
Sort: PDF datasheet
File language: English
Application: input power line for extended input module.
Length: 1.0m.
Auxiliary parts for FX3GC and FX3UC. Signal level: the DC5V, 12V, and 24V differential output can be connected to the DC5V terminal by connecting terminals.
Applicable PLC:FX1N, FX2N, FX3U, FX2NC (to FX2NC-CNV-IF).
Applicable PLC:FX3UC (to FX2NC-CNV-IF or FX3UC-1PS-5V) MITSUBISHI FX3U-32BL PDF catalog.
Can be single phase, dual phase 50kHz hardware counter high-speed input FX3U-32BL
High speed uniform output function with hardware comparison circuit.
In the dual phase count, 1, 2, and 4 multiplication modes can be set.
Can be licensed and reset by PLC or external input.
Differential output type encoder. Power: 15kw.
Purpose: high frequency braking resistor.
The use rate of the built-in regenerative brake of the transducer can be promoted MITSUBISHI FX3U-32BL PDF catalog.
When using the FR-ABR type brake resistor, the short circuit piece between the terminal PR-PX is removed. Does not remove the short circuit chip will lead to overheating of the brake resistor.
The utilization rate of the regenerative braking should be less than the allowable brake use rate in the above table.
With the operating frequency of the brake resistor to reach 300 degrees C or higher, it is necessary to take protective measures and cooling MITSUBISHI FX3U-32BL PDF catalog.
MYS type resistor can be used. But please pay attention to the allowable brake use rate.
Do not remove the terminal P/+ and P1 between the short circuit chip, in addition to connecting the DC reactor.
The installation of thermal relay, to avoid overheating and burn the braking resistor. Power: 75kw.
Voltage: 200V.
The power factor of the input power factor is up to 0.99 and above (100% load).
Can be connected to multiple inverters, to achieve a common DC bus mode.
Equipped with standard power retrogradation function. Analog output expansion board (1 channel).MITSUBISHI inverter FR-A740 series.
Voltage level: 3 phase 400V.
Frequency converter capacity: 280KW.
Frequency converter is the application of frequency conversion technology and micro electronics technology, by changing the motor operating power frequency mode to control the AC motor power control equipment.
The converter is composed of rectifier (AC), filter, inverter (DC), braking unit, driving unit, micro processing unit of the detection unit FX3U-32BL PDF datasheet.
Inverter by the internal IGBT to adjust the output power supply voltage and frequency,
According to the actual needs of the motor to provide the required power supply voltage, and then achieve the purpose of energy savving, speed control, in addition to the,
Inverter has a lot of protection functions, such as over current, over voltage, overload protection and so on FX3U-32BL PDF datasheet.
Related products
MITSUBISHI
Extended power unit
FX3U-1PSU-5V
MITSUBISHI Extended power unit FX3U-1PSU-5V
Function: extended power unit. DC5V powe
MITSUBISHI
PLC
FX3U-64MT/ESS
MITSUBISHI PLC FX3U-64MT/ESS
Max input / output points: 64 points. Su
MITSUBISHI
RS-422 cable
GT10-C10R4-8PL
MITSUBISHI RS-422 cable GT10-C10R4-8PL
Cale length: 1m. The connection etween
MITSUBISHI
Analog input module
FX2NC-4AD
MITSUBISHI Analog input module FX2NC-4AD
Numer of input channels: 4 channels. Vo