Axis of control: 2.
Interpolation: there are.
Program memory: built-in 7.8k step RAM.
Applicable PLC:FX1N, FX2N, FX3U, FX2NC (to FX2NC-CNV-IF).
Applicable PLC:FX3UC (to FX2NC-CNV-IF or FX3UC-1PS-5V).
Can control 2 axes for linear interpolation, arc interpolation.
Can not be connected to the PLC, while running alone MITSUBISHI PLC PDF datasheet.
1 can control 1 axes,
FX1N, FX2N, PLC FX3U up to 8 units can be connected,
PLC FX2NC up to 4 units can be connected,
FX3UC PLC can connect up to 7 units, and a plurality of shafts can be independently controlled FX3G-40MT/DS
Can output up to 200kHz of the pulse train.
The connection function of the absolute position detection function and the manual pulse generator.
Can be used in the form of flow chart programming software, visual programming MITSUBISHI PLC PDF datasheet. Max input / output points: 14 points.
Power supply voltage: DC24V.
Input points: 8 points.
Output points: 6 points.
Output type: relay.
Power consumption (W): 32.
Weight (kg):0.4.
Size (WxHxD) mm:90x90x75.
FX1N series is a very powerful micro PLC, can be extended to up to 128 I/O points,
And can increase the special function module or the expansion board MITSUBISHI PLC PDF datasheet.
Communication and data link function options make FX1N in the volume, communication and special function modules and other important applications is very perfect.
A PLC unit can output 2 100KHz pulses at the same time,
PLC is equipped with 7 special positioning instructions,
Including zero return, absolute position readout, absolute or relative drive, and special pulse output control FX3G-40MT/DS PDF datasheet FX3G-40MT/DS PDF datasheet. Master station module for CC-Link/LT.
I/O control can be used in the province of CC-LINK/LT.
Is to make PLC CC-LINK/LT as the main station of the FX system module.
The master station module and the remote I/O module can be connected by a special connector, and achieve the purpose of the distribution of the province FX3G-40MT/DS PDF datasheet.
Up to 64 remote I/O station modules can be connected.
Remote I/O module is assigned a common X, Y soft components,
By using the same procedure as the common input and output.
Even if the use of 2 points, 4 points of the remote I/O module, the number of soft components can be continuously assigned,
So it can be efficiently allocated I/O. Max input / output points: 48 points.
Power supply voltage: 24VDC.
Input points: 24 points.
Output points: 24 points.
Output type: Transistor (source).
Power consumption: 30W.
Weight (kg):0.85.
Size (WxHxD) mm:182x90x87.
Developed a range of special function modules to meet the needs of different - analog I/O, high speed counter.
Positioning control to achieve the 16 axis, the pulse train output or for the J and K type thermocouple or Pt sensor developed the temperature module.
A total of 8 special function modules can be configured for each FX2n main unit.
Note recording function, Component annotation can be recorded in the program register.
Online program editor, online change the program will not lose the working hours or stop production operation.
RUN/STOP switch, running on panel / stop switch easy to operate.
Remote maintenance, remote programming software can monitor, upload or uninstall programs and data via modem communications
Password protection, using a eiight digit password to protect your program FX3G-40MT/DS PDF catalog.
Clock function and hour meter function, all of the PLC FX2N has a real-time clock standard.
Continuous scanning function, to define the operation cycle for the application off the continuous scan time MITSUBISHI PLC PDF datasheet.
Input filter adjustment function, you can use the input filter to smooth the input signal (in the basic unit x000 to x017).