Max input / output points: 10 points.
Power supply voltage: 24VDC.
Input points: 6 points.
Output points: 4 points.
Output type: Transistor (source).
Power consumption (W): 6.
Weight (kg):0.22.
Size (WxHxD) mm:60x90x49.
All equipment is digital input and output point.
The total I/O points are not more than 30 points, and the input points are less than 16, the output points are less than 14 MITSUBISHI FR-A846-00250-2-60 PDF datasheet FR-A846-00250-2-60
Its MT series of PLC can drive 2 way servo or stepper, commonly used in the control system for a simple manipulator.
MITSUBISHI FX1S series PLC is suitable for the smallest package,
It is the preferred target for low cost users to seek powerful control over a limited range of I/0.
FX1S provides up to 30 I/O points, and can be transmitted through serial communication data,
MT models also have the ability to locate, widely used in a variety of small mechanical equipment MITSUBISHI FR-A846-00250-2-60 PDF datasheet. Voltage input: DC0~10V, DC0~5V.
Current input: DC4~20mA.
Voltage output: DC0~10V, DC0~5V.
Current output: DC4~20mA.
Applicable PLC:FX1N, FX2N, FX1NC, FX2NC (to FX2NC-CNV-IF).
Applicable PLC:FX3UC (to FX2NC-CNV-IF or FX3UC-1PS-5V) MITSUBISHI FR-A846-00250-2-60 PDF datasheet.
8 bit binary resolution analog input and output modules.
Input output mixed module with 2 channel analog input and 1 channel analog output.
Voltage input and current input of 2 channels can be carried out.
1 channel analog output can be the output voltage or current output. Control mode: 2 position control, PID control (with self tuning), PI control.
Control operation period: 500ms.
Applicable PLC:FX1N, FX2N, FX3U, FX2NC (to FX2NC-CNV-IF).
Applicable PLC:FX3UC (to FX2NC-CNV-IF or FX3UC-1PS-5V).
2 pass temperature input and 2 channel transistor output,
1 modules can be 2 systems for temperature regulation.
Single module to support PID (with self tuning), 2 position control, PI control.
Can be detected by the current detector (CT) is out of line. CC-Link interface module.
PLC FX can be used as the CC-LINK remote device station connection.
If using CC-LINK type FX2N-16CCL-M system master module,
So just PLC CC-LINK can build FX system. Can be used as a screw relay terminal. Positive common end use.Total input and output points: 48 points.
Input points: 24 points.
Output points: 24 points.
Output type: relay output.
Power supply voltage: AC100-240V.
Input signal voltage: AC100V.
8K capacity of the RAM memory, the maximum can be extended to 16K.
CPU arithmetic processing speed of 0.08 S/ basic instructions.
On the right side of the FX2N series can be connected to the input and output expansion modules and special function modules.
The basic unit is built in the 2 axis independent maximum 20kHz positioning function (transistor output type).
Quick disconnect the terminal block, which adopts excellent maintainability to quickly disconnect the terminal blocks, even if the cable is then replaced by the cable.
Clock function and hour meter function, all of the PLC FX2N has a real-time clock standard.
Continuous scanning function, to define the operation cycle for the application of the continuous scan time.
Input filter adjustment function, you can use the input filter to smooth the input signal (in the basic unit x000 to x017).
Note recording function, Component annotation can be recorded in the program register.
Online program editor, online change the program will not lose the working hours or stop production operation FR-A846-00250-2-60 PDF catalog.
RUN/STOP switch, running on panel / stop switch easy to operate.
Remote maintenance, remote programming software can monitor, upload or uninstall programs and data via modem communications
Password protection, using a eight digit password to protect your program FR-A846-00250-2-60 PDF catalog.