LK Automation Limited LK Automation Limited
Download Sort: OMRON | MITSUBISHI | Proface | Mennekes | Yaskawa
Catalog Download >> AJ35TB2-8D
AJ35TB2-8D PDF catalog MITSUBISHI DC input module AJ35TB2-8D datasheet PDF datasheet
Product model: AJ35TB2-8D
Name: DC input module
Brand: MITSUBISHI
Sort: PDF datasheet
File language: English
2 slots.
Can be installed in the power supply unit for A series units installed QnA/.
Cannot extend.
Relay output interface circuit of PLC
Working process: when the internal circuit output digital signal 1,
There is a current flowing through, the relay coil has a current, and then the normally open contact is closed,
Provide load current and voltage MITSUBISHI DC input module PDF datasheet.
When the internal circuit outputs a digital signal 0, there is no current flowing through it,
The relay coil does not have a current, and the normally open contact is broken off,
A current or voltage that is disconnected from the load AJ35TB2-8D
It is through the output interface circuit to the internal digital circuit into a signal to make the load action or not action MITSUBISHI DC input module PDF datasheet.
I/O points is an important indicator of PLC.
Reasonable selection of I/O points can not only satisfy the control requirements of the system,
And the total investment of the system is the lowest.
The input and output points and types of PLC should be determined according to the analog quantity and switch quantity of the controlled object,
Generally an input / output element to take up an input / output point MITSUBISHI DC input module PDF datasheet.
Taking into account the future adjustment and expansion,
In general should be estimated on the total number of points plus the amount of spare 20%~30%.
The following describes the centralized control system I/O points of the estimate AJ35TB2-8D PDF datasheet. SUMINET-3200 network.
MITSUBISHI PLC detection, fault diagnosis and display and other procedures AJ35TB2-8D PDF datasheet.
These procedures are relatively independent, generally in the basic completion of the program design and then add.
MITSUBISHI PLC protection and chain procedures.
Protection and chain is an indispensable part of the program, must be carefully considered.
It can avoid the control logic confusion caused by illegal operations AJ35TB2-8D PDF datasheet. Input and output points: 2048 points.
Input / output data points: 8192 points.
Program capacity: 30K.
Basic command processing speed (LD command) s:0.15.
Integral type: the PLC components are installed together or a few pieces of printed circuit board,
And together with the power supply installed in the casing to form a single overall called the host or the basic unit, small, ultra small PLC using this structure.
Modular: PLC is the basic components of a separate module.
Medium and large PLC used this way. Easy maintenance.
Each scanning process. Focus on the input signal sampling. Focus on the output signal to refresh.
Input refresh process. When the input port is closed,
Program in the implementation phase, the input end of a new state, the new state can not be read.
Only when the program is scanned, the new state is read.
A scan cycle is divided into the input sample, the program execution, the output refresh.
The contents of the component image register are changed with the change of the execution of the program.
The length of the scan cycle is determined by the three.
CPU the speed of executing instructions.
Time of instruction.
Instruction count.
Due to the adoption of centralized sampling.
Centralized output mode.
There exist input / output hysteresis phenomena, i.e., the input / output response delay.
User program storage capacity: it is a measure of how much the usser application can store the number of indicators AJ35TB2-8D PDF catalog.
Usually in words or K words as units. 16 bit binary number is a word,
Every 1024 words are 1K words. PLC to store instructions and data in words.
General llogical operation instructions each account for 1 words MITSUBISHI DC input module PDF datasheet. Timer / counter,
Shift instruction accounted for 2 words. Data operation instructions for 2~4.
Related products
MITSUBISHI
Analog module
AJ35T-M04B-R
MITSUBISHI Analog module AJ35T-M04B-R
Analog channel: 4 channels. Input / outp
MITSUBISHI
Transistor output module
AJ35TB1A-8T
MITSUBISHI Transistor output module
 AJ35TB1A-8T
Output points: 8 points. Output voltage
MITSUBISHI
Silicon controlled output module
AJ35TJ-8S1
MITSUBISHI Silicon controlled output module
 AJ35TJ-8S1
Output points: 8 points. Output voltage
MITSUBISHI
Relay output module
AJ35TB2-8R
MITSUBISHI Relay output module
 AJ35TB2-8R
Output points: 8 points. Output voltage